SITUATION 17:A 3 meter cantilever hollow circular bar6 mm thick with outer diameter of 300mm is subjected to a torque of 25 kNmat free end and G = 35GN/m?.50. Determine the maximum stress dueto torque.а. 24.8 МPаc. 18.6 MPab. 31.3 MPаd. 48.7 MPa51. Determine the maximum angle oftwist.a. 1.025°C. 2.240°b. 1.948°d. 2.508°52. If the bar is solid, find the torsionalstressа. 4.72 МPаc. 8.6 MPab. 3.3 MPаd. 6.7 MPa6 mm thickL=3md=288 D=300 mmT=25 kNm

Answered: Image /qna-images/answer/26bd11ff-63bd-4606-83d4-2f5dc23af483.jpg

SITUATION 17: A 3 meter cantilever hollow circular bar 6 mm thick with outer diameter of 300 mm is subjected to a torque of 25 kNm at free end and G= 35GN/m?. 50. Determine the maximum stress due to torque. а. 24.8 MPа C. 18.6 MPa b. 31.3 MPa d. 48.7 MPa 51. Determine the maximum angle of twist. a. 1.025° C. 2.240° b. 1.948° d. 2.508° 52. If the bar is solid, find the torsional stress a. 4.72 MPa C. 8.6 MPa b. 3.3 MPa d. 6.7 MPa

SITUATION 17: A 3 meter cantilever hollow circular bar 6 mm thick with outer diameter of 300 mm is subjected to a torque of 25 kNm at free end and G= 35GN/m?. 50. Determine the maximum stress due to torque. а. 24.8 MPа C. 18.6 MPa b. 31.3 MPa d. 48.7 MPa 51. Determine the maximum angle of twist. a. 1.025° C. 2.240° b. 1.948° d. 2.508° 52. If the bar is solid, find the torsional stress a. 4.72 MPa C. 8.6 MPa b. 3.3 MPa d. 6.7 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB.
5. A hollow 3-m-long steel shaft must transmit a torque of 25 kN · m. The total angle of twist in this length is not to exceed 2.5° and the allowable shearing stress is 95 MPa. Determine the inside and outside diameters of the shaft in millimeters if G = 85 x 10° Pa. The maximum shearing stress occurs at the outer fibers at D/2.
Help?
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
Q1. The solid shaft has a radius of 4 cm a. Find the state of stress at H. b. Draw the Mohr's circle for the state of stress at H. c. Find the principal stresses and orientation of principal planes, and the maximum shear stress and its orientation at H. P PL B= 8= AE V 2,₂ = 2/- (0₂+0₂) 2y = 7/7 - (0₂+0₂) Ex 6cm 8= 100 N Pdx √" (= AE V 4-7-7 (9₂ +9₂) == EE To AL 729 12 cm 10 cm My 50 N E uz 100 N 8cm 8cm 100 N 시구
Situation 1. A closed cylindrical tank 500mm in diameter and made of 2mm thick plate is subjected to an internal pressure, p=1MPa and an axial tensile force, F-25kN. 1. Determine the longitudinal and tangential stresses (MPa) produced in the wall of the tank, respectively. A. 70.46, 125 B. 132.95, 62.5 2. On a plane making an angle of 25° with the longitudinal axis of the tank, calculate the normal stress. A. 113.84 B. 120.37 C. 62.5, 125 D. 125, 70.46 A. 23.94 B. 20.89 C. 115.26 D. 80.20 3. On a plane making an angle of 25° with the longitudinal axis of the tank, calculate the shear stress. C. 26.99 D. 17.53
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
The shaft in the figure has a hollow part from B to A and is solid throughout C to B. The hollow segment is 8mm thick and the shaft has an outer diameter of 80mm. Determine the maximum shear stress developed in the shaft. If B is the midpoint of the 2-meter shaft, and G = 75 Gpa, determine the angle of twist of A with respect to C. PROBLEM 1 B 4 kN-m 2 kN-m
A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 10.8 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. P A B D L Answer: Tmax = psi /3 /3
A stainless steel (G = 86 GPa) shaft has four segments and four torques. Find the max shaer stress and rotation at a section 4 m from the left end. The maximum shear stress in each segment. The amount of twist for each segment, and the roation of the right end with respect to the left end.
P1.4 Three solid bars, each with square cross sections, make up the axial assembly shown in Figure P1.4/5. Two loads of P = 30 kN are applied to the assembly at flange B, two loads of Q = 18 kN are applied at C, and one load of R = 42 kN is applied at end D. The bar dimensions are b₁ = 60 mm, b₂ = 20 mm, and b3 = 40 mm. Determine the normal stress in each bar. (1) b₁ B P (2) FIGURE P1.4/5 (3) Q D R