A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 10.8 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D Answer: Tmax psi /3 1/3

A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 10.8 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D Answer: Tmax psi /3 1/3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

o
2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm fasten together as shown in the figure. Determine the safe diameter of the fasteners if the fasteners as spaced 100mm apart. The allowable shear stress in rivets is T = 145 MPa. 0 A P=20 kN 4m
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
The cross section of the beam in the figure is made of 100 mm x 20 mm boards. It is manufactured by screwing each other and the distance between the screws is 50 mm. and the shear force is V = 2500 N. Safe slipping for screw material Since the stress value is τem = 50 MPa, the screw that can be used in connection Find the diameter. dimensions in mm
A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a pure torque of T = 4420 lb-ft. Determine the maximum inside diameter d that can be used if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 3° in an 8-ft length of shaft. O 3.07 in. O 2.38 in. O 2.75 in. O 2.52 in. O 1.50 in.
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
#2 handwritten then box the final answers
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
1. A solid steel shaft 3in in diameter and 4ft long is fixed at one end and free at the other, as shown. The shaft is subjected to an axial tensile load of 50,000 lbs. a. Compute the magnitude of the force P at the free end necessary to reduce the stress at point B to zero. b. Compute the maximum combined stress at point A. 50.000 b 4'-0"
make it understanda
A solid steel shaft supports loads PA = 570 N and PD = 430 N, as shown. Assume L1 = 250 mm, L2 = 510 mm, and L3 = 230 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 38 MPa, determine the minimum diameter d that can be used for the shaft.
A 0.475 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L= 14.4 in., and the load applied to each pulley is P 66 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. P. D A P. Answer: psi Ancwonr Tmax /3 /3 B. 13