A 38-mm-diameter solid steel shaft supports loads PA = 1610 N and Pc = 3030 N, as shown. Assume L₁ = 135 mm, L₂ = 177 m and L3 191 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of the maximum bending stress in the shaft 4 Answers: On L₂ L3 MPa. x = mm.

A 38-mm-diameter solid steel shaft supports loads PA = 1610 N and Pc = 3030 N, as shown. Assume L₁ = 135 mm, L₂ = 177 m and L3 191 mm. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of the maximum bending stress in the shaft 4 Answers: On L₂ L3 MPa. x = mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
3. Two-solid 2.0-in.-diameter steel shafts are connected by the gears shown. The shaft length are L, = 12 ft and L2 = 20 ft. Assume that the shear modulus for both shafts is G = 12,000 ksi and that the bearings shown allows rotation of the shafts. If the gear at D is rotated at an angle of 8°, what is the maximum shear stress in each shaft. L2 Rg = 5 in. (1) B Tp (2) Rc = 3 in. D
A solid circular bronze [G = 6,500 ksi] shaft, 6.2 ft long and 1.150 in. in diameter, carries a torque of 85 lb-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax psi (b) Ф%3
A long shaft of diameter d is subjected to twisting moment T at its ends. The maximum shear stress acting is equal to A zero B с D 16T d³ 32T +d³ 64T +³
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
1. A solid steel shaft 3in in diameter and 4ft long is fixed at one end and free at the other, as shown. The shaft is subjected to an axial tensile load of 50,000 lbs. a. Compute the magnitude of the force P at the free end necessary to reduce the stress at point B to zero. b. Compute the maximum combined stress at point A. 50.000 b 4'-0"
make it understanda
A solid steel shaft supports loads PA = 570 N and PD = 430 N, as shown. Assume L1 = 250 mm, L2 = 510 mm, and L3 = 230 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 38 MPa, determine the minimum diameter d that can be used for the shaft.
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
show steps At point (A)
A 29-mm-diameter solid steel shaft supports loads PA = 1100 N and Pc = 2810 N, as shown. Assume L₁ = 105 mm, L₂ = 176 mm, and L3 = 210 mm. The bearing at B can idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of the maximum bending stress in the shaft. Answers: max = 1₂ Po MPa, x = mm.