A composite bar consist of a core snuggly fitting inside a tube. A force F is applied to the ends of the bar.Part of the force is carried by the tube and part of the force is carried by the core. The tube and the core have equal elongation.Calculate the elongation of the composite bar (8).L→F15Your unique values to use are (everybody will get different values for every question):F45,000 NL0.8 m400 mm²150 mm²205 GPa140 GPaACOREATUBEECOREETUBEYour mihe haced entirely on t+ from holow

Answered: sist of a core snuggly fitting inside a…

sist of a core snuggly fitting inside a tube. rried by the tube and part of the force is ca tion of the composite bar (8). 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!
2.65 The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod?
The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 61 GPa] with a cross-sectional area of A₁ = 810 mm². Bar (2) is a bronze alloy [E = 103 GPa] with a cross-sectional area of A2 = 470 mm². Assume L₁=2.4 m, L₂=3.1 m, a=0.7 m, b=1.9 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 5.8-mm clearance in the pin connection at A. If a load of P = 44 kN is applied at B, determine: (a) the normal stresses 0₁, 0₂, in both bars (1) and (2). (b) the normal strains &1, 82, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. A Answers: (a) 0₁ = (STVA = a i i B 156.10 0.00256 b C MPa, 0₁ = με, €2 = mm L2 i i D 20.75 0.0002014 MPa. με.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each materials given that P = 10kN?
Determine the stresses in each bar and the bond reactions.
A2
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₁ = 820 mm². Bar (2) is a bronze alloy [E = 117 GPa] with a cross-sectional area of A₂ = 420 mm². Assume L₁=1.9 m, L₂=2.5 m, a=0.7 m, b=1.9 m, and c=1.3 m. All bars are unstressed before the load P is applied; however, there is a 1.4-mm clearance in the pin connection at A. If a load of P = 34 KN is applied at B, determine: (a) the normal stresses 0₁, 02, in both bars (1) and (2). (b) the normal strains &1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) ₁: (c) VA = = tel i L₁ B b L2 mm. C MPa, σ₁ = με, εξ = i i D MPa. με.
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₁ = 700 mm². Bar (2) is a bronze alloy [E = 106 GPa] with a cross-sectional area of A₂ = 480 mm². Assume L₁=1.8 m, L₂=2.1 m, a=0.5 m, b=1.6 m, and c=0.8 m. All bars are unstressed before the load P is applied; however, there is a 3.4-mm clearance in the pin connection at A. If a load of P = 53 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains 1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 (c) VA = i a L₁ B b (2) L2 MPa, 0₁ = με, €2 = mm. i i D MPa. με.
Calculate the support reactions of the column element given in the figure. Determine the required edge length a to ensure to safety of the element that is made of a material with a safety stress capacity of 200 MPa and that supports the column at point A. ( AB and BC parts have the same material properties. )
etermine the elongation of a 0.5-in, dianeter sterl bar The elastic modulus of the steel bar is 27000 kar. 2000 Ib 10 ft