copper tube with wall thickness of 8 mm must carry an axial tensile load of 175 kN. The allowable tensile stress is 90 MPa. Which of the ff. gives the maximum product of moment on inertia of the section in 1x 10^6 mm^4

copper tube with wall thickness of 8 mm must carry an axial tensile load of 175 kN. The allowable tensile stress is 90 MPa. Which of the ff. gives the maximum product of moment on inertia of the section in 1x 10^6 mm^4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

Q: 2. The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls.…

A: Length of bar, L =3mCross sectional area of bar, A=350mm2Initial temparature, t1 =20°CCoefficient of…

Q: The uniform beam of weight W is to be supported by the two rods, the lower ends of which were…

Q: In a simply-supported beam loaded as shown below, the maximum bending moment in Nm is 1000 mm 500 mm…

Q: What are the major functions of a project coding system?

A: Project-coding systems are used to help organize planning efforts for all kinds of business.…

Q: The aluminum rod AD (E=73 GPa, a=23x10-6/°C) has a diameter of 15 mm and is attached to the rigid…

A: Given E=73 GPa, a=23x10 -6/°C diameter =15 mm temperature T, = 30°C. temperatureT2 = -20°C,

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. IfP-7…

Q: 1

A: Given data:- Moment about a horizontal axis on the cross section is 0.80 kN-m

Q: Problem 2: A shaft is to be fitted with a flanged coupling having 6 bolts on a circle of diameter…

A: As per guidelines we can solve one question at a time,here student ask for question number 2 hence,…

Q: solve for the angular deformation of one end relative to the other end

Q: A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂…

A: G = 10.93 MPaP = 13 kN or 13000 N

Q: Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional…

A: Given data, Normal stress = 450 MPa Angle = 35 ° Point load = 20 kN UDL = 8 kN/m To find out the…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

Q: Question 2 A compound shaft consists of copper rod of 30 mm diameter enclosed in a steel tube of…

A: Given data -Diameter of copper rod (di) = 30 mm Diameter of steel rod (do) = 50 mm T = 1000 Nm = 1…

Q: Determine the maximum force P that can be applied to the specimen. The bar is made from steel and…

A: w=150 mmh=50 mmr=20 mmt=6 mmwh=15050=3rh=2050=0.4From graph, K=1.51σavg=σallK =1501.51…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

Q: Steel A-450 mm² E-200 GPa L-4.0 m A B opper A=230 mm² E-120 GPa L= 3.0 m 5.0 m a) What maximum P can…

Q: Problem 1 A bar obtained by bonding together pieces of aluminum (E, = 70 GPa) and brass (E, = 105…

A: We have to determine the value of largest moment M that can be applied about the horizontal axis…

Q: the temperature of the rigid bar is -45 degrees celsius. A close fit exists at both of the rigid…

A: Given data in question Length Area Elasticity modulus Coefficient of thermal expansion Change in…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

Q: eed the answer to the question in engineering resistance

A: GIVEN E=38 GPA lA=5 mm lB=3mm

Q: 60MM PL 30 мм 30 мм комм 40 MM то

A: Hello dear Please find the attached solution below, thanks

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

A: Given- Length L=1.5 m, Square section 40 mm side, Stresses- σx=310 N/mm2,σy=-300 N/mm2,E=2×105…

Q: At 130°C, a bronze hoop 20 mm thick whose inside diameter in 600 mm just fits snugly over a steel…

A: The values given in the question are as follows Bronze hoop thickness=20 mm Inside diameter of…

Q: a) The principal planes b) The principal stresses c) The stress components exerted on the element…

A: Question is based on the element subjected to axial, compression and shear stress . Magnitude of…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A: Given data Diameter of brass rod (dB) = 32 mm Diameter of steel tube (ds) = 50 mm Gs = 2GB T =…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A: To determine the maximum shear stress developed in steel.

Q: Below is another BA bar attached to the AD bar. Diameter of DA bar is 0.02M. A force F = 1000N is…

Q: The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is…

A: Given data Steel and bronze bar Area Youngs modulus Length Stresses To find out Maximum value of P

Q: 8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a…

A: Using equilibrium conditions, ∑H = 0HA = 0∑V = 0RA+RB = P∑M at A = 0P×2 = RB×4RB = P2Using the above…

Q: A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the…

Q: A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm,…

A: Given data :We have to calculate the elongation of the bar

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

Q: Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if…

Q: An aluminum tube with the hexagonal cross-section shown is 2.5 ft long and has a constant wall in.…

A: Given data- An aluminium tube with hexagonal cross section Length (L) = 2.5 ft Constant Wall…

Q: Q-A uniform prismatic circular bar made up of rigid material is subjected to a tensile force of 5000…

A: Tensile force F=5000 N Diameter of cross-section d=7 mm It is needed to find the stress and strain…

Q: 600 400 600 800 Gl P2 P3 E F Tha at y pnywty A - 100 mm" E- 200 GPa A- 150 mm E- 200 GPa A130 mm E-…

Q: Calculate the stress in the copper bar (in MPa). b)Calculate the axial deformation in the brass bar…

Question

copper tube with wall thickness of 8 mm must carry an axial tensile load of 175 kN. The allowable tensile stress is 90 MPa.

Which of the ff. gives the maximum product of moment on inertia of the section in 1x 10^6 mm^4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

answer quickly
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
The 1154-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 424 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 148 MPa and 86 MPa, respectively. Express your answer in two decimal places.
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²
A hollow titanium [G = 46 GPa] shaft has an outside diameter of D = 56 mm and a wall thickness of t = 1.88 mm. The maximum shear stress in the shaft must be limited to 243 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 27 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 75 kW is being transmitted at 9 Hz. Answers: (a) P = i (b) = kW.
how can i solve this one please
A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of diameter 50 mm. 2GB) Both shafts are firmly (Gs jointed. The combined assembly is subjected to a torque of 1000 Nm. calculate maximum shear stress = developed in steel in N/mm2 (up to 2 decimals)
79. A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius of 10 m by applying a pure moment M. If Young's modulus E = 200 GPa, then the magnitude of M is (1) 72 Nm (2) 144 Nm (3) 216 Nm (4) 288 Nm
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P= 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. e 5P 39 E-200 GP gomm 30 mm 30 mvm 80 mm 30 mm 30 mm
The equation of deformation is derived to be y = x³ - xL for a beam shown in the figure. YA The curvature of the beam at the mid-span
Asap
k=17 p=117kN Strength of material question. without taking into account wire thickness.