2.65 The rigid bar of negligible weight is pinned at O and attached to two verticalrods. Assuming that the rods were initially stress-free, what is the largest load P thatcan be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa inthe bronze rod? -2m-1.5m-1.5mSteelA = 900 mm²E = 200 GPaL = 1.5 mFIG. P2.65BronzeA = 300 mm²E = 83 GPaL = 2m

Answered: Image /qna-images/answer/a43c6100-c013-470d-8be8-772b81de2b5c.jpg

Answered: -2m- 1.5m-1.5m Steel A = 900 mm² E =…

Engineering

Civil Engineering

-2m- 1.5m-1.5m Steel A = 900 mm² E = 200 GPa L = 1.5 m FIG. P2.65 Bronze A = 300 mm² E = 83 GPa L = 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
Need correctly in neat and clean handwritten solution explaining every steps
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₁ = 700 mm². Bar (2) is a bronze alloy [E = 106 GPa] with a cross-sectional area of A₂ = 480 mm². Assume L₁=1.8 m, L₂=2.1 m, a=0.5 m, b=1.6 m, and c=0.8 m. All bars are unstressed before the load P is applied; however, there is a 3.4-mm clearance in the pin connection at A. If a load of P = 53 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains 1, 2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar. (1) A Answers: (a) σ₁ = (b) 1 (c) VA = i a L₁ B b (2) L2 MPa, 0₁ = με, €2 = mm. i i D MPa. με.
Topic: COMBINED STRESS-AXIAL TENSION AND FLEXURE BENDING: STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
Problem 3 (20 minutes) The bars' assembly has the dimensions, diameters and materials indicated (EST 29,000 ksi; EBR = 15,000 ksi). The assembly is fixed at one end and has D in, E = 1. 10 in and F20 kip. Determine the normal force N in the bronze and the steel = d=2in = 30 d= 1 in F(kip) BRONZE ← STEEL A B ↑ c D(in) Elin 2. Draw the normal force diagram along the assembly 3. Determine the elongations ALAB (of portion AB), ALBC (of portion BC) and ALAC
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F