Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally spaced from the center of the section, with shearing capacity t=100 MPa, for bearing ob = 220 MPa for rivets in single shear and Ob = 280 MPa for rivets in double shear. E=200GPA for all materials. 8 KN 15 KN/m 12 KN/m A E 2m 3m 3m 2m Properties of T-Section Bf = 180 mm Tf = 16 mm Tw = 12 mm D = 210 mm Properties of C-Section Bf = 105 mm Tf = 12 mm Tw = 12 mm D = 210 mm

Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally spaced from the center of the section, with shearing capacity t=100 MPa, for bearing ob = 220 MPa for rivets in single shear and Ob = 280 MPa for rivets in double shear. E=200GPA for all materials. 8 KN 15 KN/m 12 KN/m A E 2m 3m 3m 2m Properties of T-Section Bf = 180 mm Tf = 16 mm Tw = 12 mm D = 210 mm Properties of C-Section Bf = 105 mm Tf = 12 mm Tw = 12 mm D = 210 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 16 mm-diameter steel rod AB is fitted to a round hole near end Cof the wooden member CD. For the loading shown, determine, (a) the distance b for which the average shearing stress is 7MPA on the surfaces indicated by the dashed lines, (provide FBD and answer in mm)(b) the average bearing stress on the wood (provide FBD and answer in MPa) 25 mm. 8000N 4000N A 100 mm D 4000N C
Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. 30 degrees Assume U= 0.85. All steel will be A36. PL늘X1 C10 C10 11 in PL x 11 11 in
7. Determine the horizontal shearing stress at 95 mm above the Neutral Axis. 8. Determine the spacing of the bolts.
In a truss girder of a bridge, a diagonal consists of mild steel flat 400 ISF and carries a pull of 80 tonnes. If the gross diameter of the rivet is 26 mm, the number of rivets required in the splice is.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
Reinforce an existing simply supported W16 x 36 beam made of A36 steel to carry a service dead load of 0.5 kip/ft and a service live load of 1.1 kip/ft. The beam spans 25 ft and is fully braced by the floor. WELD ALONG THE LENGTH AND ENDS WELD ALONG THE LENGTH AND ENDS A (b) (s) EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM
I. Solve the given problem below. 1. Atension member has a span of 7.6 m and carries a tensile load of 512 kN. The member is to have two lines of rivets in each flange for the 20 mm rivets with standard diameter of 22 mm for hole dimension with at least 3 rivets in a line. Using an A 36 W section and neglecting the weight of member, design a W section. Fy 248 MPa and Fu = 400 MPa. Possible Sections: W 8 x 17 A = 3232 mm2 d = 200 mm r=85.34 mm ry 30.99 mm t = 7.82 mm b 133.4 mm W 5 x 18.5 A = 3503 mm2 d = 130 r= 54.86 mm ry = 32.51 mm tr 10.67 mm b = 127.6 mm W 250 x 67 A = 3794 mm2 d = 157 r= 67.56 mm ry 38.35 mm tr = 9.32 mm br = 152.9 mm %3D %3D %3D %3D %3D
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment of inertia of the section in x10^6 mm^4
Please solve question c
(Design Of Steel Structures) 4. Beam ISLB 500 at 750N/m carries total factored uniformly distributed load of 300kN. It is supported on columns ISHB300 at 630N/m at each end. The connection is made is using M20 bolts of grade 4.6 and steel Fe410. Design the connection.