Problem 1 A C180x15 attached to a W250 x 18 section as shown and bolted by bolts having a diameter of 15 mm. а. Determine the location of the neutral axis from the top of the beam. ANS b. Determine the moment of inertia of the combined section. c. Determine the maximum spacing for the bolt if fv =100 MPa ANS ANS d. Determine the maximum bearing stress exerted by the bolts. ANS 15mm diameter bolts section

Problem 1 A C180x15 attached to a W250 x 18 section as shown and bolted by bolts having a diameter of 15 mm. а. Determine the location of the neutral axis from the top of the beam. ANS b. Determine the moment of inertia of the combined section. c. Determine the maximum spacing for the bolt if fv =100 MPa ANS ANS d. Determine the maximum bearing stress exerted by the bolts. ANS 15mm diameter bolts section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right solution according to the question. The tension member L 5 x 3 x 1/2 is used to carry the deadload of 42 kips and liveload of 23 kips with an 7/8 inch diameter attached. A36 is used. Determine its adequacy based on: a.LRFD b. ASD
A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, Fy = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20. b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20. 210 mm Tension Plate M20 bolts
The flanges of a W200x52 G40.21-350W steel tension member are connected to 16 mm gusset plates using 12-M22 bolts as shown in the figure below. Determine the tensile resistance of the member. [Hint: You will need to consider shear lag] 30 75 75 38
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole Compute the nominal strength in bearing on Gusset plate only (since this will govern, it has smaller thickness than the main member PL ½ x 6)
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
Please solve the ff and write legibly SN = 38 Determine the adequacy of the W8x58 subject to the following: Axial Tension: DL = 100 kN + SN, LL = 120KN + SN Axial Compression: DL = 60 kN + SN, LL = 80KN + SN L = 8m 2 holes for 20mm.dia. bolts Fy = 250 Mpa Fu = 400 Mpa
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
SITUATION I A lapped bolted lension member is shown. Diameter of bolts are 22 mm and the plate material is A36 steel Fy = 275 MPа, Fи 3 415 МPа. Assume the fasteners are adequate and do not control the tensile capacity. Diameter of hole is 2.5 mm bigger than the diameter of bolt. 12 :: 350 50 100 100 50 50 1. Determine the tensile capacity of the lapped joint based on gross area. a. 252.656 kN c. 866.250 kN b. 202.125 kN d. 693.000 kN 2. Determine the net Area for the tensile capacity of the lapped joint. а. 3318 тm? c. 5250 mm? b. 1554 mm? d. 1824 mm? 3. Determine the tensile capacity of the lapped joint based on the net area. a. 752.856 kN C. 866.250 kN b. 688.845 kN d. 1039.500 kN
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
please solve 1.3
Compute the nominal strength based on yielding in KN. Determine the allowable tensile strength of Plate A in KN. Compute the allowable tensile strength at section a-1-2-2-4-c in KN.