1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a X -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 16-in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest loadP that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B C 6 in. 4 in. Fig. P1.51 三。

1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a X -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 16-in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest loadP that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B C 6 in. 4 in. Fig. P1.51 三。

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20 2okN KN Hinge B I the max nagative bonding momut at A

Q: Determine the maximum load P that can be applied to the lap joint connected by three – 16 mm…

A: STEEL STRUCTURES:

Q: ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and…

Q: 2-A teel pod is sfreteked between fwo rigid walls ard carries a tensile Coad f GO00N at C.f the…

Q: Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000…

A: a ) P = 9000 lb and F = 3000 lb Compute the stresses at A and B ? Solid mechanics problem.

Q: NS 5 ft iG B 920 lb 1145 lb 1760 lb -20 ft20 ft 20 t 20 -20120 t-

A: To find the force in member CD , ND and NK -

Q: Q3 The cantilevered bar in the Fig 3 is made from a cast iron material and is statically loaded with…

A: Perhaps the main part of building a house is structural engineering and design. Structural…

Q: 1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in…

Q: identify the zero force member// statics

A: The given structure is:-

Q: M Deter MINE THE MAX Dez of the Beam

Q: Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin…

A: To find out the normal stress in rod 1 and shear stress in pin A and B.

Q: P1.020 For the clevis connection shown in the figure, determine the maximum applied load P that can…

A: d = 15 mm = 75 MPa

Q: -A 8teel pod is stretcke between two rugid walls ard carries a tensile Coad f GO0ON a C If the…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

A: Given, A1 = 1.5 in2 dpin = 0.7 in a = 47 in b = 96 in

Q: Determine the no. of rivets to fasten the member BD

A: GIVEN: 1. Rivet strengths at working conditions : In Shear = 70 MPa In Bearing = 140 MPa 2.…

Q: D Front view 18 mm 6 mm B IB Side view 160 mm 120 mm Top view In the steel structure shown, a…

Q: SOLVE FOR THE FORCE IN MEMBER XY AND YZ

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: Given data: Shear stress τ = 70 MPa Bearing stress σ = 140 MPa Diameter of rivet d = 19 mm For the…

Q: A joint connection is shown below. If the average shear stress in the pin must not exceed 107 MPa,…

A: Given: Max. shear stress = 107MPa, D=12mm = 12*10-3 Ma. applied load, P= ?

Q: Beam AB is supported as shown in Figure. Tie rod (1) is attached at B and C which are double-shear…

A: Data Given: w = 1800 lb/ft σs = 54 ksia = 15 ftb = 30 in.c = 7 ft.fy = 36 ksiFOS = 2.5 Asked:…

Q: 20 2okN Hinge A C Find the max nagative bonding momen nt at A due to Moving load.

Q: s to be made of steel having an ultimate shearing stress of 400 MPa, determine: (a.)The diameter of…

Q: In the steel structure shown, a 6-mm-diameter pin is used at Cand 10-mm-diameter pins are used at…

A: To find value of load P

Q: Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as…

Q: The

Q: I diametér ssive load Pacting wi e stresses at one of t

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P =…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

Q: A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections…

A: For the given roof truss:

Q: Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Shear Stress : Shear stress is the force which causes the deformation of a structure, component or a…

Q: 2,300 mm A 1,150 mm 1,600 mm 75 kN

Q: A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is…

Q: Find the stresses of FAB. FAc. FBC & FBD- 20 k 15 k 60 60 60 60

Q: Determine the principal stresses. Show all results on complete sketches of differential elements.…

Q: Problem 1: The truss shown below is made of fiberglass member section and an axial strength of 14…

A: Given : Axial strength = 14 MPa dia of high strength nylon pins = 20 mm Shear strength = 25 MPa…

Q: Homework: A helica) cast steel with 30 helix angle has to tanmit 35 KW at 15oo yon. Gear has 24…

A: given data,helix angle α=30∘power P=35KW=35×103WN=1500rpmno of teeth T=24σ0=56MPa=56N/mm2face…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

1.51 Link ACis made of a steel with a 65-ksi ultimate normal stress and
has a X -in. uniform rectangular cross section. It is connected
to a support at A and to member BCD at C by -in.-diameter pins,
while member BCD is connected to its support at B by a
16-in.-diameter pin. All of the pins are made of a steel with a 25-ksi
ultimate shearing stress and are in single shear. Knowing that a
factor of safety of 3.25 is desired, determine the largest load P that
can be applied at D. Note that link AC is not reinforced around the
pin holes.
8 in.
B
D
6 in.
4 in.-
Fig. P1.51

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

IDENTIFY THE ZFM ZERO FORCE MEMBERS
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
Find the stresses in A, B and C? 14-d Vem 14 6m 0.006 MN 0 cm B -HA- 4 IX 6em H
a steel tube sandwiched between two rods, one of aluminum and the other of bronze, and as shown in Fig. 110 - P. The axial loads indicated. Calculate the maximum value of P so that the stress does not exceed in aluminum, MPa 80, in steel 150 MPa, and in bronze 100 MPa.
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC Is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60 mm outside diameter and 30-mm inside diameter Determne the maximum shearing stress in the aluminium in MPa if a torsional load ot 4000 N m is applied at B. Ends A and Carerigidly damped. 45 mm 60 mm 30 mm 12m
The lap joint is fastened with four 3/16-in.-diameter rivets. The working stresses are 58 ksi for the rivets in shear and 10 ksi for the plates in bearing. in.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
13
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co