Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. Assume U= 0.85. All steel will be A36. 30 degrees

Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. Assume U= 0.85. All steel will be A36. 30 degrees

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: ✓ Ultimate tensile strength of each member CD is 300 ksi Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in: C and D-2 in E and F - 1 in. 1.5 in. thick Support Plates -2 ft + D 3 ft B 2 in thick Support Mate Solution Step 1. Identify the conditions for design. Stress normal stress in each member CD, OCD shear stress in bolt A, TA shear stress in bolt C, T shear stress in bolt E, T shear stress in bolt F, T bearing stress on member BDE due to: bolt B, BDE-B bolt D, OBDE-D bolt E, OBDE-E bearing stress on support plates at…
Please help with the problem below
PL 5/8 x 12 3/4-in-diameter bolts
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
SOLVE FOR1 HR
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co