(Design Of Steel Structures) 4. Beam ISLB 500 at 750N/m carries total factored uniformly distributed load of 300kN. It is supported on columns ISHB300 at 630N/m at each end. The connection is made is using M20 bolts of grade 4.6 and steel Fe410. Design the connection.

(Design Of Steel Structures) 4. Beam ISLB 500 at 750N/m carries total factored uniformly distributed load of 300kN. It is supported on columns ISHB300 at 630N/m at each end. The connection is made is using M20 bolts of grade 4.6 and steel Fe410. Design the connection.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
From the Truss member shown, design all the tension members for ASD and LRFD, if the connection for the angle bars are shown. Use A36 STEEL. 100 mm 150 mm 2.5 m B SERVICE DEAD LOAD =300 KN SERVICE LIVE LOAD = 200 KN 2 m 2 m 2 m 2 m
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
The three-plate moment connection shown below are all shop- welded to the column and then field bolted to the girder. The beam is a W18 55 that has a factored moment of Mr = 382 kip ft and a factored shear of V₁ = 65 kip. All plates are A36 steel (Ex = 36 ksi. Fu = 58 ksi). Plate 2 is connected to the girder using four bolts as shown. All bolts for the connection are 7/8" diameter A325-X. Plate2 Plate 1 2.00" 2.75" 2.75" 2.75" 2.00" Plate3 W18 55 3.00" 2.50" (a) Design Plate 1, including the required number of bolts and dimensions of the plate. Assume an E70XX weld to the column. Consider limit states only for the plate itself. That is, you do not need to consider limit states for the beam or column. (b) For which plate(s) will you need to check the buckling capacity, Plate 1, 2, and/or 3? Explain.
The welded frame beam connection consists of the framing angle 100 x 75 x12.5mm and the column W12 x 72. The welds are 9mm fillet welds made with E70 electrodes. All members are A36 steel. 12.5 mm a.) Determine Pu base on the capacity of the welds. Use LRFD design Factors. W 12x72 Angular Section 75 m 18.75 18.75 Angular section Angular section 800
Reinforce an existing simply supported W16 x 36 beam made of A36 steel to carry a service dead load of 0.5 kip/ft and a service live load of 1.1 kip/ft. The beam spans 25 ft and is fully braced by the floor. WELD ALONG THE LENGTH AND ENDS WELD ALONG THE LENGTH AND ENDS A (b) (s) EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM
1- The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of shear stresses. (St-37, H) t= 20 # ##* JL 90.90.9 40 50 315 9,96 t 9,04 t 9,40 t 9,70 t
Problem 2: Book Problem 3-9 (Hint: Only one of the two chains is at max tension, the other will be less.) 3-9. Determine the maximum force F that can be supported in the position shown if each chain can support a maximum tension of 600 lb before it fails. 30° SERDISC A Prob. 3-9 C
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Cocoo Answer:dmin- P in.
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.² and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b A kips P Answer: Pallow= i a B