simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of threa

Q: d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731…

A:

Q: (9) A single thread trapezoidal metric thread has a pitch of 4mm &has a mean diameter of 18mm. It is…

A: Given data: p=4 mmd=18 mmdo=37 mmdi=27 mmm=400 kgμ=0.3 Need to determine the required torque.

Q: A steel bolt 25 mm in diameter carries a load of 4 kN in tension. Estimate the tensile stress of the…

A: Given data Load= 4 kn Diameter of bolt = 25 mm Diameter of thread = 20 mm Find the tensile stress at…

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

A:

Q: The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb.  Rapid cycling…

A:

Q: In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each…

A: Shearing stress is defined as the ratio of load to the shear area. When this shearing stress exceeds…

Q: i kullanılmıştı ancı bölgesind

A: Given:  Power to be transmitted = 0.67 KW Rotational speed = 900 KPM Gear width = 20 mm Yield…

Q: Q6 A screw clamp as shown in the figure, exerted load (30KN), and the type of thread is (Tr.70×8.5).…

A: exerted load= 30 KNThe type of thread is  ( Tr. 70 x 8.5)Stress for nut = 60 MPaLength of the nut =…

Q: In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded…

A: P =331.7lb D=1 inch coefficient of friction (K) =0.2135 for 1030 hot rolled carbon steel tensile…

Q: A square-thread power screw has d = 37 mm, d = 34, a pitch of 6 mm with double threads, f=f =0.05, d…

A: Power screw It is a device which converts rotary motion into linear motion.  It is also called as…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: 10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of…

A: Given Screw clamp To find Torque it can handle

Q: Identify the flange thickness (in mm) of a flange coupling having 6 bolts, that is 10-mm in…

A: Write the expression of torque transmitted to the flange. Tflange=nd1tfσcfD12      ......…

Q: A circular bar is to carry a fluctuating torque from 25 to 55 N-m. Use AISI C1144 OQT 1000 for the…

A: Given: Torque, T=25 to 55 N-m Factor of safety, n=2 Stress concentration factor, kf=2.5 To find:…

Q: A 25 mm diameter steel bar is loaded in double shear until failure, the ultimate load is found to be…

A:

Q: A vehicle jack has single start square thread, a 20 mm major diameter and a pitch of 3 mm. A plain…

A: thread root diameter = diameter - pitch = 20-3 = 17mm

Q: A double riveted single cover butt joint (zig zag arrangement), is used for connecting two plates…

A: Given:- Permissible shearing stress in rivets = 120 MPa- Permissible tensile stress in plate = 150…

Q: The figure shows the handle super fast byke and its geometry with forces The cross section at the…

A: Given data  Major axis = 3in Minor axis = 1.5in  Load = 20kip  To estimate  Stresses of the inner…

Q: Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two…

A: Given Data The diameter of the shaft is: d=50 mm The yield strength of the shaft is: σy=440 MPa The…

Q: 1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is…

A: Treat the shaft as simply supported beam with supports at A and D.Here  are reaction forces at…

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia =…

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in

Q: PROVIDE FREE-BODY-DIAGRAM IN EVERY LETTER. Show clear hand writing and complete solution. Thank you…

A: Given: The load, P = 275 kN

Q: (12) A turnbuckle connects two rods having %-16 UNC threads. The thread friction is 0.2. How much…

A: Write the given data. μ=0.2P=500 lbdm=0.335 in

Q: 2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N…

A:

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data  Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: A 20 mm diameter bet having a diameter at the toot ef the thread of 18.6 mm is used to fasten two…

A:

Q: The metal stud punch shown in the figure below is designed to create circular shaped perforations on…

A:

Q: M16 x 2.0 ISO 5.8 coarse series bolts and nuts clamp a 26-mm-thick steel cover plate to a 6-mm-thick…

A:

Q: cross section, side length b, and wall thickness t. The second is a round of diameter b and wa…

A:

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: Q4/A/Determine the Maximum axial stress for a36-ftjoint of 7.625-in.OD.6.625in.ID,39 Ib/ft. N-80…

A:

Q: Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and…

A: Given data: The bending moment is M=1 kNm=106 Nmm The turning moment is T=1 kNm=106 Nmm The ultimate…

Q: Bolts distributed about a bolt circle are often called upon to resist an external bending moment as…

A:

Q: be made of tempered wire. Since the material is to be subje and fatigue must be considered a low…

A:

Q: for the lap joint shown below, calculate the safe axial tensile fo 126 102 A 220M

A:

Q: Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A=…

A: Given data: Stress in steel σs=120 Mpa Stress in bronze σb=70 Mpa Steel Properties  Asteel=900 mm2…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.