• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft• Briefly describe which type of shaft is more effective.• See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page. WeldNarrowslit1 = 0.156OT+d = 3.188→Ed = 3.188--D = 3.500–-ED = 3.500(a) Closed tube(b) Open tubeFIGURE 3-12 Comparison of closed andоpentubesunits, inches.to the shaftsapply the same torgueof each type (closed vs vpen),Q) when weT = 10* binレン Lo inT matG : 10 psimax7VSclosedopen

Narrow slit 3D 0.156- Weld +d = 3.188 D = 3.500- Ed = 3.188– ED = 3.500 %3D %3D (a) Closed tube (b) Open tube FIGURE 3-12 Comparison of closed and open tubes vnits? inches. Q) when we apply the same torque to the shafts of each type Cclosed vs opon), T= 10* bin Lo in G= 10" psi ニ T max' T mat VS cloced Open

Narrow slit 3D 0.156- Weld +d = 3.188 D = 3.500- Ed = 3.188– ED = 3.500 %3D %3D (a) Closed tube (b) Open tube FIGURE 3-12 Comparison of closed and open tubes vnits? inches. Q) when we apply the same torque to the shafts of each type Cclosed vs opon), T= 10* bin Lo in G= 10" psi ニ T max' T mat VS cloced Open

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve the following problems and SHOW YOUR COMPLETE SOLUTIONS FOR BETTER UNDERSTANDING
Need only a handwritten solution only (not a typed one).
Could you answer quickly pls? ( course: strength of materials 1)
Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880 N and T2-432 N. The maximum bending moment is at x =230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm 280 mm 30-mm dia. 300 mm 250-mm dia. 400-mm dia. 270 N X. 1800 N
Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque 624 (T).
Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
Pls solve this, subject is machine design
Problem 5 only, solve carefully, include the units in every step and draw the diagram. Thanks! A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2times that of the inside diameter. Find the inside and outside diameters in mm.
A solid 1.2 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3200 lb·in. What horsepower must be delivered to the shaft to maintain a shaft speed of 690 rpm? What is the maximum shear stress developed in the shaft?
Q5 The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power to a mating gear that drives a mixer. Gear C delivers power to a different mating gear that drives a circular saw. All power comes into the shaft through gear B. Considering only torsion, compute the shearing stress in each part of the shaft. Consider stress concentrations, Material 1144 OQT 1300 GearA=10kw, Gear C=15kw. Ø20.0 A 30.0 Retaining ring 3x Ø40.0 Ø28.0 Groove B Ø50.0 Ø30.0 Bearing Profile keyseats at A, B, C Fillet radius= 1.00 mm at each step Dimensions in mm Ø20.0 C -Ø15.0
(2) The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel. | Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft D
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts