d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside diameter of washer 9/8 inch Tensile stress in the nut = 18 ksi Bearing stress = 800 psi Required: 5/8 in 1. Shearing stress in the head of the bolt 2. Shearing stress in threads of the bolt 3. Outside diameter of the washer 0.731 7/8

d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside diameter of washer 9/8 inch Tensile stress in the nut = 18 ksi Bearing stress = 800 psi Required: 5/8 in 1. Shearing stress in the head of the bolt 2. Shearing stress in threads of the bolt 3. Outside diameter of the washer 0.731 7/8

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Answer number 1 only
answer only 2 . Shearing stress in threads of the bolt
1-69.M Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be if the circular shank of the bolt pulled out from the head, a shearing action. Compute the shear stress in the head for this mode of failure if a force of 22.3 kN is applied. Applied force Shear area Reaction force on underside of head Cylindrical shear area 19.0 mm 8.00 mm -12.0 mm M12 x 1.75 thread
This is the answer only write hand written plz asap..... I'll rate for sure
HOW TO SOLVE: Draw the FBD of one member Solve for the bearing force. Section one bold and solve internal forces. Solve for the normal and shear stress in the bolts. Solve for the bearing stress in the members due to the nuts. Solve for the bearing stress in the members due to bolts. ANSWERS: bearing stress of bolt= 7.96 MPa, T; shear stress of bolt= 13.78 MPa; bearing stress (max)= 18.04 MPa
How the sec (alpha) value is measured 29/2? Can you please describe the circled line in details.Thank you
10/10 find the shear stress in bolt in pin A 60 kN 2. 4 M 3 BOLT DIA 20 MM A 50 kN PIN A 159 MPa 636 MPa 79 MPa O 318 MPa (
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? a. 8mm b. 3/8 inch 25 kN 12 mm C. 10 mm d. 1/2 inch 7.5 mm 12 mm 7.5 mm 25 kN 18. The motion of the follower of a cam-follower system is governed by x = R(1+1/2 coscot). If R = 70 mm and (= 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 c. 22 d. 24 b. 20
Answer as many as you can, no solution needed
A,B,C,D,E,F,G WHICH POINT PLS WRITE THE LETTER AS UR FINAL ANSWER THX
Q1 A single-square thread power screw is to raise a load of 100KN. The screw has a major diameter of 42 mm and a pitch of 6 mm. The nut for the screw transfers the load as shown in the F/2 F/2 figure right. The power screw is made of carbon steel having Sy=350MPA and Sut= 500MPa. The nut is to be made of ASTM 25 gray cast iron having S,=220MPA and Suc=670MPA. The friction on the screw threads is 0.15 and the friction on the nut is ignored. Calculate; i) ii) iii) iv) Raising and lowering torques Efficiency for raising the load Check for the self-locking condition Nut height (h) when considering the failures due to direct shear at the root of the thread and bearing stress failure on nut. Take the factor of safety as 3. Critical load when the power screw is at maximum height of 850mm. v)