The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2 - C, grade 5.8, with rolled threads as shown in the figure below, on which an external load P 10 kN/bolt is applied. km=5.5kb. Steel bolt k=ka End plate Cylinder

Q: Which of the following statement is incorrect? Select one: O Friction is high for dry surface O…

A:

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: Write the SI units of work done.

A: Work is defined as the product of the displacement and the component of force along the…

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: What about density?

A:

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: What is the frictional Force

A:

Q: In a machine, the maximum torque transmitted by a shaft exceed by 15 % the actual torque. A power of…

A:

Q: Define the following phrase; i. External forces ii. 111. iv. V. Forces generated by motion Forces…

A:

Q: 15B) Before the object start moving, If applied force is increased, then friction force will a.…

A:

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: 350 lb 30 250 lb

A:

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: 1. What do you mean by measurement? Why it is needed?

A:

Q: A screwdriver is a kind of wheel and axel machine where the radius of the handle is the input…

A: Given data: The diameter of handle, d1 = 1 in. The diameter of the shaft, d2 = 1/4 in. Write the…

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: angular velocity is equal........

A: Angular velocity is equal 2πN60

Q: What is quasistatic compression ?

A: "Quasi-static processes" are ideal reversible processes which cannot occur in practical(real…

Q: What is the unit of surface tension.

A: Unit of surface tension

Q: pascal

A: given: what is pascal law?

Q: -differe nce b etwee

A:

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: How does the tension in the string change as the masses start to move? Or does it?

A: Consider pulley mass system as shown in the figure below, Scenario 1 Assume the pulley does not…

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: Define the term work of force?

A: Work of force is defined as the dot product of force and displacement  W=F.S…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: 13A) coefficient of friction (H) is O a. normal force + limiting friction O b. normal force limiting…

A:

Q: The direction of the frictional force: O Always opposes the motion or the tendency to motion. O Is…

A: The direction of frictional force has been asked:

Q: (5) In order to forge a pure gold ring, you first need to purchase the gold. The ring design is a…

A: According to Pappus–Guldinus theorem volume can be given as V=Ax2π×yArea of the block as per given…

Q: The Figure to the right shows a manufacturing process? What is this process called? 2. Identify the…

A: Given :-  1. What is the process called ?

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.