Section-B A rough pipe of diameter 45 cm and length 500 m carries water at the rate of 0.4 m³/s. The wall roughness is 0.012 mm. Determine: (i) the coefficient of friction (ii) wall shear stress (iii) centre-line velocity (iv) velocity at a distance of 15 cm from the pipe wall d Take =2 210g101 K, +1.14

Section-B A rough pipe of diameter 45 cm and length 500 m carries water at the rate of 0.4 m³/s. The wall roughness is 0.012 mm. Determine: (i) the coefficient of friction (ii) wall shear stress (iii) centre-line velocity (iv) velocity at a distance of 15 cm from the pipe wall d Take =2 210g101 K, +1.14

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation: A 50 mm diameter bracket is securely fastened to the wall as shown. It carries the given horizontal and vertical loads. 90 mm 4000 N 150 mm 3600 N 1. Find the maximum normal stress at point A. a. 28.02 MPa b. 34.82 MPa b. 41.22 MPa d. 44.72 MPa 2. Find the minimum normal stress at point A. a. - 14.82 MPa c. - 24.82 MPa b. - 4.22 MPa d. - 4.72 MPa 3. Find the maximum shearing stress at point A. a. 28.02 MPa b. 34.82 MPa b. 41.22 MPa d. 44.72 MPa
Cylindrical tank with closed ends is filled with compressed air at a pressure of 480 KPa. The inner radius of the tank is 2 m, and it has wall thickness of 6 mm. Find magnitude of maximum in plane shear stress.
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmokie
Problem 2 Water flows through a horizontal 45 degree bend with a 22-in dimeter at a rate of 20 ft³/s under a pressure of 15 lb/in². a. In the x-direction P₁ b. In the y-direction y κα F *P2, Fx F Neglecting the head loss in the bend, calculate the resisting force required to anchor this pipe bed: X
A concentrated load of P = 29 kN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe. B Ⓒ 3.24 MPa O 2.41 MPa O 2.80 MPa O 3.57 MPa O 3.90 MPa O
A vertical propane tank with an outside diameter of D=300 mm and a wall-thickness of t=14 mm is subjected to a horizontal force of F = 41 kN. The gage pressure inside the tank is 6 MPa. [D=300 mm, t=14 mm, F=41 kN, h = 1 m] Determine the shear stress produced by the applied force at K. 0 MPa 17.91 MPa 6.51 MPa 19.5 MPa 7.61 MPa Feedback: Shear stress is developed at point k due to the applied force P. Correct answer: 6.51 MPa
Cylindrical tank with closed ends is filled with compressed air at a pressure of 480 KPa. The inner radius of the tank is 2 m, and it has wall thickness of 6 mm. Find magnitude of maximum in plane shear stress.
Q| As shown in figure below, determine the weight of concrete cylinder, for equilibrium the gate AB. The gate AB weighs 20 kN. Pulley Cable Cable Gate wide 3m B Concrete cylinder 90° Water Sm 2.5m 30 Hinge
Q-The flow of water (mass density - 1000 kg/m³) and kinematic viscosity = 106 m² /sec, a compressible pipe with equivalent roughness Ks as 0.12mm yields average shear stress at the pipe boundary = 600N/m². The value of Ks/8' (8' being the thickness of laminar sublayer) for this pipe is ...
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29
A square steel tube having the cross section shown is used as a column of 26-ft effective length to carry a centric load of 65 kips. Knowing that the tubes available for use are made with wall thicknesses ranging from 14 in. to 34 in. in increments of 116 in., use allowable stress design to determine the lightest tube that can be used. Use σY= 36 ksi and E= 29 x 106 psi.
Cylindrical tank with closed ends is filled with compressed air at a pressure of 340 KPa. The inner radius of the tank is 1 m, and it has wall thickness of 4 mm. Find magnitude of maximum in plane shear stress.