A vertical propane tank with an outside diameter of D=300 mm and a wall-thickness of t=14 mm is subjected to a horizontal force of F = 41 kN. The gage pressure inside the tank is 6 MPa. [D=300 mm, t=14 mm, F=41 kN, h = 1 m] Determine the shear stress produced by the applied force at K. 0 MPa 17.91 MPa 6.51 MPa 19.5 MPa 7.61 MPa Feedback: Shear stress is developed at point k due to the applied force P. Correct answer: 6.51 MPa

A vertical propane tank with an outside diameter of D=300 mm and a wall-thickness of t=14 mm is subjected to a horizontal force of F = 41 kN. The gage pressure inside the tank is 6 MPa. [D=300 mm, t=14 mm, F=41 kN, h = 1 m] Determine the shear stress produced by the applied force at K. 0 MPa 17.91 MPa 6.51 MPa 19.5 MPa 7.61 MPa Feedback: Shear stress is developed at point k due to the applied force P. Correct answer: 6.51 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two steel [E = 29,500 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in. and a wall thickness of 0.283 in. Pipe (2) has an outside diameter of 4.375 in. and a wall thickness of 0.204 in. Assume L₁= 15 ft and L₂= 25 ft. If the normal stress in each steel pipe must be limited to 18 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) (b) Pmax VB= (1) = i i C B kips in.
When filled to capacity, the unpressurized storage tank contains water to a height of h=41ft. The outside diameter of the tank is 8.9 ft and the wall thickness is 0.502 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.) Answers: Maximum normal stress σ= i Maximum shear stress 7= i psi. psi
The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress developed at points A and B. These points lie on the pipe’s outer surface. Sketch the shear stress on volume elements located at A and B. . The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and it is subjected to the uniformly distributed torque along its entire length, determine the absolute maximum shear stress in the pipe. Discuss the validity of this result.
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of 0.383 in. The pipe is subjected to a uniformly distributed torque of t = 87 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c = 7.75 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. Answers: ccccccccc.com (a) TA= a (b) TB = i b i psi psi
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
A horizontal load Pof magnitude 96 kN is applied to the beam shown. Determine the largest distance a for which the maximum tensile stress in the beam does not exceed 75 MPa. 20 mm 20 mm P. 20 mm 60 mm 20 mm The largest distance a is mm.
Problem : Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hooke's Law (E) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters?b) Check whether the pressure vessel is safe or not? Given data: - The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal stress is σL = 200 MPa.Hooke's Law (E) = 150 MPaThe radial stress is σR = -50 MPa.
A high-strength steel [E = 188 GPa] tube having an outside diameter of 67 mm and a wall thickness of 4.1 mm is bent into a circular curve having a 42-m radius of curvature. Determine the maximum magnitude of the bending stress max developed in the tube. Answer: Omax = i MPa.
Required information The tube shown has a uniform wall thickness of 12 mm. Take P = 19 kN. D HP E 28 KN 28 KN Determine the stress at points A and B. 16.11 MPa. The stress at point A is The stress at point B is MPa. 125 mm 75 mm
A water tank 5m in diameter and 5m high is made from steel having a thickness of 12mm. Answer below, a.) When the tank is filled with water, determine the circumferential stress. b.) Determine the longitudinal stress at the bottom of the tank when it is filled with water. c.) If the circumferential stress is limited to 5MPa, what is the maximum height of water to which the tank maybe filled.
3.) A tube with E=10x106 psi is used to support a compressive load. The maximum allowable change in length is 0.025 percent, determine (a) the maximum normal stress in the tube (b) the minimum wall thickness for a load of 1600 lb if the outside diameter of the tube is 2.0 in.