A concentrated load of P = 29 KN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe. B 3.24 MPa O 2.41 MPa O 2.80 MPa O 3.57 MPa O 3.90 MPa L O

A concentrated load of P = 29 KN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe. B 3.24 MPa O 2.41 MPa O 2.80 MPa O 3.57 MPa O 3.90 MPa L O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a…

Q: The circular tube with the cross section shown is subjected to the axial force P and bending moment…

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: 50 cm-long circular rod has a diameter of 10 mm and is acted pon by a 20 kN load acting to its…

A: Length of rod = 50 cm Diameter of rod = 10 mm Load = 20 KN E = 200 Gpa

Q: 2. The column shown is made of steel (E-29,000ksi) and has a square cross-section of 6 in x 6 in. A…

A: Given:- The modulus of elasticity of steel (E) = 29000 ksi The square cross-section = 6 in × 6 in…

Q: 1. Mohr's Circle. Determine the radius of the circle (R) and the coordinates for the center of the…

A: X axis represents normal stress and y axis represents Shear stress.

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

Q: A thin walled tube of thickness (t) 5mm and diameter (d) 200mm with closed ends is subjected to an…

A: We knowσa=Pd4t and σC=Pd2tτ=T2πr2tso,Axial stress :σx=Pd4t=72004×5Mpa=70MpaCircumferential Stress…

Q: A solid 2.40 in. diameter shaft is subjected to a torque of T = 330 lb-ft and an axial load of P =…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Principal stresses: Principal stress is defined as the plane's zero shear stress. The principal…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

A concentrated load of P = 29 kN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330
mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe.
B
Ⓒ 3.24 MPa
O 2.41 MPa
O 2.80 MPa
O 3.57 MPa
O 3.90 MPa
O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction step of the question

VIEW

Step 2: calculation step

VIEW

Step 3: calculation step

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Required information The line of action of the 75-kip axial load Pis parallel to the geometric axis of the column AB and intersects the x axis at x = 0.6 in. Use E= 29 x 106 psi. W8 x 35 0.6 in.. B 20 ft Determine the maximum stress in the column. (Round the final answer to two decimal places.) The maximum stress in the column is 10 ksi.
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
Situation The helical spring shown is axially loaded with a compression force P equal to 5 kN. The mean diameter of the spring is 100 mm and the wire used is 10 mm as indicated in the figure. 1. What is the shear stress at A? 2. What is the shear stress at B? 3. On diameter AB, locate the point of zero stress measured from C. P = 5 kN WW P = 5 kN 100mm A 10mm B
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…
Required information The tube shown has a uniform wall thickness of 12 mm. Take P = 19 kN. D HP E 28 KN 28 KN Determine the stress at points A and B. 16.11 MPa. The stress at point A is The stress at point B is MPa. 125 mm 75 mm