A tube with external diameter 50 mm and 5 mm thickness is subjected to loads as shown in Fig. . Determine the sate of stress at point A (0, 25, 0) and B (0, -25, 0) and principal stresses. 0.5 kN 500 mm- 200 mm 1.5 kN

A tube with external diameter 50 mm and 5 mm thickness is subjected to loads as shown in Fig. . Determine the sate of stress at point A (0, 25, 0) and B (0, -25, 0) and principal stresses. 0.5 kN 500 mm- 200 mm 1.5 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.125 in. and a wall thickness of 0.286 in. Pipe (2) has an outside diameter of 4.000 in. and a wall thickness of 0.209 in. Assume L₁ = 13 ft and L₂= 21 ft. If the normal stress in each steel pipe must be limited to 24 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) Pmax= (b) VB= (2) (1) tel i tel P C B kips in.
answer quickly
Problem-3 b. A water main 160 cm dia. Contains water at a pressure head of 200 m. Take weight of water to be 1000 kg/m³. The thickness of the metal shell required for the water main given that the maximum permissible stress in the metal is 400 kg/cm², will be...
During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d;) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L) is 2.625 inches. Answer the questions below: Us TR 70- 60 - Lo LyP *IR 50 - EL PL: proportimal limit EL Elastic limit UXP = 4pper yield point Lyp : Lower us : uiti mated streagth IR : Indicanteed Strengty Rupture TR: True strength Ruptue 40 AL or 8t P 30 **PL (proportimal limt) Direct strain E strain (in/in) aStress Iblinz (esi) 0.003. ogo o-200
Q..c,.
Required information The tube shown has a uniform wall thickness of 12 mm. Take P = 19 kN. D HP E 28 KN 28 KN Determine the stress at points A and B. 16.11 MPa. The stress at point A is The stress at point B is MPa. 125 mm 75 mm
A water tank 5m in diameter and 5m high is made from steel having a thickness of 12mm. Answer below, a.) When the tank is filled with water, determine the circumferential stress. b.) Determine the longitudinal stress at the bottom of the tank when it is filled with water. c.) If the circumferential stress is limited to 5MPa, what is the maximum height of water to which the tank maybe filled.
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.
show steps At point (A)
3. Two bars are rigidly fastened together and support a vertical load of 65 kN, as shown. The upper bar is steel having length 10 m and cross-sectional area 70 cm². The lower bar is brass having length 6 m and cross-sectional area 40 cm². For steel E = 200 GPa, for brass E= 100 GPa. Determine the maximum stress in each material. A] A 10 m B B 6 m 65 KN