The copper pipe [G = 6,000 ksi] has an outside diameter of 3.750 in. anda wall thickness of 0.250 in. The pipe is subjeted to a uniformly distributed torque of t 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b 3.5 ft, and c 8.5 ft, determine. (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft. a В Answers: (a) Tmax = 0.665 ksi (b) Pc = 0.008488 rad eTextbook and Media

The copper pipe [G = 6,000 ksi] has an outside diameter of 3.750 in. anda wall thickness of 0.250 in. The pipe is subjeted to a uniformly distributed torque of t 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b 3.5 ft, and c 8.5 ft, determine. (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft. a В Answers: (a) Tmax = 0.665 ksi (b) Pc = 0.008488 rad eTextbook and Media

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The diameter of the shaft, shown below, is 60 mm and it is made of A-36 steel (E = 200 GPa and G = 75 GPa). The shaft is fixed at its ends A and B and is subjected to the loadings shown. Determine the absolute maximum torsional shear stress in the shaft. 500 N-m 200 N-m 1.5 m
1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It is fixed at A and three torques are applied to it as shown. Find the maximum shear stress in the pipe and the rotation at the free end assuming linear elastic behavior. 4 m 80 N-m m Im 20 N-m 30 N-m
Determine the principal stress
The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimum shear stresses on the shaft’s surface and specify their locations, measured from the free end. . The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the required diameter d of the shaft if the allowable shear stress for the material is tallow = 60 MPa.
Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is subjected to a uniform axial distributed loading along its length of w3- loads also act on the rod: P= 1900 lb and Q =500 lb. Assume a = 21 in. and b = 42 in. Determine the normal stress in the rod at the following locations: = 975 lb/ft. Two concentrated %3D (a) x = 14 in. (b) x = 42 in. C b. a Answer: psi Ox=14in. psi Ox=42in. Attempts: 0 of 1 used Subr Save for Later
A force of 3000N is acting on the orange plank which is attached to the pin as shown in thefigure. a.) If the thickness of the orange plank is 75mm and the pin has a diameter of 20mm,compute the bearing stress acting between the plank and pin. b.) Compute theshearing stress acting on the pin and c.) the normal stress of the orange plank if it hasa width of 500mm.
Please answer asap with clear and complete solutions .thank you
The diameter of the shaft, shown below, is 60 mm and it is made of A-36 steel (E = 200 GPa and G = 75 GPa). The shaft is fixed at its ends A and B and is subjected to the loadings shown. Determine the absolute maximum torsional shear stress in the shaft. 500 N-m 200 N-m 1.5 m
Problem 3.1. A 1-in-diameter solid bar (), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), cuch supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)lf the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, e, of the tubular member? I in. 1=0.2 in. (1) (3)
a.) In ksi b.) In rad
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) оp1 — 3940 рsi, Op2 -1980 psi, o p3 D0 (b) op1 = 83 MPa, o,2 = 60 MPa, O,3 = 0 Answer: (a) Tabs max psi = (b) Tabs max= MPa
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.