Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone clutch to increase torque. The cone clutch has an outer diameter of 500 mm and inner diameter of 300 mm. the cone has a face angle of 12.5° and a width of 45 mm. The coefficient of friction of 0.25 and normal pressure on the clutch face is not to exceed 0.1 N/mm? 3.1. Sketch the cone clutch and indicate all dimensions and forces. 3.2. Cakulate the axial thrust. 3.3. Cakulate axial spring force to engage. 3.4. Derteimine the wear. 3.5. Find torque.

Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone clutch to increase torque. The cone clutch has an outer diameter of 500 mm and inner diameter of 300 mm. the cone has a face angle of 12.5° and a width of 45 mm. The coefficient of friction of 0.25 and normal pressure on the clutch face is not to exceed 0.1 N/mm? 3.1. Sketch the cone clutch and indicate all dimensions and forces. 3.2. Cakulate the axial thrust. 3.3. Cakulate axial spring force to engage. 3.4. Derteimine the wear. 3.5. Find torque.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Q2/ A conical clutch an included angle of 60°. the outer radius and inner diameters are 80 and 20 cm respectively. Calculate the maximum and minimum intensity of pressure and force required to press the two halves together if it is to transmit 20 MW, at 60 rev/h. the coefficient of friction is 0.3, Use both the uniform wear theory and the uniform pressure theory.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
Solve show solution
Q1 Q5) Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm, load factor is 2 and the mean diameter to face width ratio is 6.
Q3-a/ What are the characteristics of material which used for lining friction surfaces of a clutch? (5Marks) b/ An engine developing 45 kW at 1000 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed (0.1 N/mm2). Determine: 1. The face width required, and 2. The axial spring force necessary to engage the clutch Answer question 4 or 5 (15 Marks) 15 Q4/ The areas of the turning moment diagram for one revolution of a multi-cylinder engine with reference to the mean turning moment, below and above the line, are - 32, + 408,-267, +333,-310, +226,- 374, + 260 and 244 mm². The scale for abscissa and ordinate are: 1 mm = 2.4° and 1 mm = 650 N-m respectively. The mean speed is 300 r.p.m. with a percentage speed fluctuation of± 1.5%. If the hoop stress in the material of the rim is not to exceed 5.6 MPa, determine the…
A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r, = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N, calculate the power that can be transmitted by drive.
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2
...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.