Q) A single plate clutch has to transmit 75 kWat 3000 r.p.m. The spring exerts an axialpressure of 7.35 N/cm3. Determine the innerand outer diameters of the friction surfaces ifthe ratio of the two diameters is 1.5.

Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of 7.35 N/cm³. Determine the inner and outer diameters of the friction surfaces if the ratio of the two diameters is 1.5.

Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of 7.35 N/cm³. Determine the inner and outer diameters of the friction surfaces if the ratio of the two diameters is 1.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A soft surface cone clutch must handle 1865 In-1b of torque at 1250 rpm. The large diameter of the…

A: Given data: Torque (T) = 1865 in-lb Speed (N) = 1250 rpm Diameter (D) = 13.75 in Included angle (θ)…

Q: A leather faced cone clutch transmits power at 500 rpm. The semi-cone angle a is 12.5°. The mean…

A: According to the given information we know that the clutch to transmit power is 500 rpm, angle is…

Q: A cone clutch with cone angle 20° is to transmit 7.5 kW at 750 r.p.m. The normal intensity of…

A: The Power transmitted by clutch can be determined by the formula given below as- P=2πNT60 where P is…

Q: H.W (1): A single dry plate clutch transmits 7.5 kW at 900 r.p.m. The axial pressure is limited to…

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: - The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of…

Q: A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters…

A: Given data:

Q: ..A cone clutch with a cone angle of 15° transmits 58 kW at 1300 rpm. The coefficient of friction of…

A: Givenθ=15oP=58kWN=1300 rpmμ=0.11Dm=250mm=0.250m

Q: A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1…

Q: THE ENGINE OF AN AUTOMOBILE IS RATED TO GIVE SOKWAT 200 RPM WITH A MAXIMUM TORQUE OF 600 N-M. DESIGN…

A: The answer is mention below

Q: A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and…

A: A multi-plate clutch is a type of clutch mechanism used in automotive and mechanical applications to…

Q: ported on two bearings as shown in Fig. 1. It car naft is receiving 20 kW at pulley A and delivering…

Q: A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact…

A: Given:Number of pairs=3Speed,N=1500rpmOuter radius,r1=100mm=0.1mInner…

Q: (b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside…

A: Given: Outside diameter, D = 380 mm or 0.38 m Inside diameter, d = 270 mm or 0.27 m Pressure, P =…

Q: mm, The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required…

A: A disc or plate clutch has the same use that a cone clutch has. Instead of two spinning discs, the…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given, Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and…

A: Clutch is defined as a machine element which is used to engage and disengage driver and driven shaft…

Q: A single plate clutch, with both sides effective has outer and inner diameters 300 mm and 200 mm…

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: A flat belt is required to transmit 35 kW from a pulley of 1.5 m effective diameter running at 300…

A: Given data: Power transmitted by the belt (P) = 35 kW Effective diameter of the pulley (d) =1.5 m…

Q: Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at…

A: Given Data: p = 30kW = 30 * 103 W N = 500rpm α = 13.4o D = 300mm => R =…

Q: Example: An automotive single -plate clutch with two pairs of friction Surfaces, transmits a 300 N-m…

A: given data;torque(T)=300N-m=300*103N-mminner diameter(d)=170mmouter diameter(D)=270mmcoefficient of…

Q: 92 A dry single plate clutch is to be designed for an automotive wehicle whose engine is rated to…

A: radius of the friction plate = r1 Inner radius of the friction plate = r2 r1 = 1.25 r2

Q: A single-plate clutch has a friction disc with inner and outer radii of 20 mm and 40 mm,…

A: Uniform pressure theory is when the product of pressure and area of the contacting surface…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: Determine the minimum applied force P required to move wedge A to the right. The spring is…

Q: A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: a. Co-efficient of friction b. Normal reaction C. Reaction force d. Limiting friction

A: Friction force has the tendency to stop impending motion.

Q: Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction

A: Given Discharge, Q = 14361.60 gpm = 0.91 m3/s Length, L = 1000 ft = 304.8 m…

Q: A multi-plate clutch as in the figure below transmits power at 1500 rpm. The coefficient of friction…

A: Clutches need a way to be activated in order to cease the transmission of torque. The clutch pedal…

Q: A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and…

A: Given: The angle of cone, 2θ = 120° The coefficient of friction, f = 0.4 The outer diameter, D = 85…

Q: A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20…

A: Given: Mean diameter, dm = 15 in or 1.25 ft Power transmitted, P = 20 hp or 11000 lb.ft/s Rotational…

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given, Coefficient of friction, μ=0.15 Weight of the handle, W=15 N Applied force to the end of the…

Q: An automobile single plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform pressure theory: When the clutch and bearing mating components are fresh, the contact…

Question

Q) A single plate clutch has to transmit 75 kW
at 3000 r.p.m. The spring exerts an axial
pressure of 7.35 N/cm3. Determine the inner
and outer diameters of the friction surfaces if
the ratio of the two diameters is 1.5.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is aPplied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Counterclockwise. 150 mm T 200 N 60 150 mmi 675 mm 75 mm
1. A single plate clutch consists of a pair of contacting surfaces. The inner and outer diameters of the friction disk are 125 and 250 mm respectively. The coefficient of friction is 0.25 and the total axial force is 15 kN. Calculate the power transmitted by the clutch at 500 rpm when using: a) The new clutch b) The worn-out clutch
Solve fast
A single plate clutch is required to transmit 150 kW at 6000 r.p.m. The clutch facings available provide a coefficient of friction of 0.25, and the average pressure is to be limited to 75 kN/m2. Determine the dimensions of the working surface of the clutch plate if its maximum dimension is not to exceed 160 mm due to space restrictions.
Draw the FBD of the problem The coefficient of friction between the inner pulley and the belt is 1/?. Find the maximum value of W that can be supported without rotating the compound pulley P or slipping the belt on the compound pulley P. Pulley B is frictionless. A C "P 200 lb A B W
How much torque can a cone clutch transmit if the angle of the conical elements is 10 degrees. The mean diameter of conical sections is 200 mm and an axial force of 600 N is applied. Consider a coefficient of friction
A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.
2. The power transmitted by a belt drive is 2.5 kW. The linear velocity of the belt is 2.5 m/s. The angle of lap on the smaller pulley is 165°. The coefficient of friction is 0.3. Determine the effect on power transmision in the following cases: (i) Initial tension in the belt is incrased by 8% by suitable dressing to the friction surface of the belt. Rover is tanemitted ring a Vhelt drin The ineud Karooun is 30 The bele
Q. A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficients of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.