Question-03: The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips when bolted between double brackets at A and B. the bar will be fabricated from 0.6inches thick plate. For the grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearing stress = σb = 55 ksi and Shearing stress = τ = 5.4ksi. Solve for the values of (a) the diameter d of the bolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.

Question-03: The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips when bolted between double brackets at A and B. the bar will be fabricated from 0.6inches thick plate. For the grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearing stress = σb = 55 ksi and Shearing stress = τ = 5.4ksi. Solve for the values of (a) the diameter d of the bolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hand written and clean writing please
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
A high-strength steel band saw, 27 mm wide, runs over pulleys 1000 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E =230 GPa. Answer must be in mm.
Y1
need answer thank you
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
Calculate the shear yield stress (ksi) of A588 steel.
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Show complete solution. Thank you
Subject: Steel design- Bolted Steel Connection - Bolted Subjected to Eccentric Loads *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
* A 76 mm x 76mm x 6mm angular section is welded to a gusset plate having a thickness of 8mm as shown in the figure. The length L1 equals 125mm and L2 is 65mm. The angular section has a cross sectional area of 929mm2, Fy=248 MPa, Fu=400MPa. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P gusset plate L₂= 65 mm 25 mm