Ql: the collar shown in figure (1) has a mass of 3 kg and attached to the light spring, which has stiffness of 35 N/m and an unstretched length of 2 m. the collar is released from rest at A and slides up the smooth rod under the action of the constant 75 N force. Calculate the velocity of the collar as it passes position B. 2 m 30 75 N k= 35 N/m 2.5 m Figure (1)

Ql: the collar shown in figure (1) has a mass of 3 kg and attached to the light spring, which has stiffness of 35 N/m and an unstretched length of 2 m. the collar is released from rest at A and slides up the smooth rod under the action of the constant 75 N force. Calculate the velocity of the collar as it passes position B. 2 m 30 75 N k= 35 N/m 2.5 m Figure (1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2. For the beam shown, choose the spring force as the redundant reaction. The modulus is E = 30 x 106 psi. Determine: a) The support reaction at the base of the spring, b) the rotation of the beam at the left support. 5000 lb/in. R₁ 500 lb/ft -20 .2 m 2² 4"
Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure. The gate is hinged along its top edge and is held in position by the force P. Neglect the friction at the hinge and weight of the gate. Determine the required value of P. V Water Hinge Gate 60° 6 ft 10 ft
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 120N/m 300 N 300 N-m 200 N 100N/m Im B 4m C Im DIm E 4m 1m G 400 N¬m
The simply supported beam AB is loaded as shown in the figure below. 1. Derive the shear force and bending moment equations for the entire beam. 2. Draw the shear force and the bending moment diagrams based on the equations derived in part 1. A 2 m. 800 N/m 3 m 4.2 kN.m 2 m2 m→ B
(b) A solid circular cross-section shaft is clamped at both ends and loaded by a twisting moment t per unit length as shown in figure below. Determine the reactive twisting moment at each end of the bar. ·1 A 13 ◄ t/ unit length C C C C C 1
5) A) Projectile motion A gun with muzzle velocity of 1200 ft/sec is fired at an angle of 8° above the horizontal. Find the horizontal and vertical components of the velocity. B) Inclined plane Suppose that a box is being towed up an inclined plane as shown in the figure. Find the force w needed to make the component of the force parallel to the inclined plane equal to 2.5 lb. 330 15° 6) A force F = 2i + j - 3k is applied to a spacecraft with velocity vector v = 3i – j. Express F as a sum of a vector parallel to v and a vector orthogonal to v. 7) a) Work along a line Find the work done by a force F = 5i (magnitude 5 N) in moving an object along the line from the origin to the point (1, 1) (distance in meters). b) Locomotive The Union Pacific's Big Boy locomotive could pull 6000-ton trains with a tractive effort (pull) of 602,148 N (135,375 Ib). At this level of effort, about how much work did Big Boy do on the (approximately straight) 605-km journey from San Francisco to Los Angeles?…
In (Figure 1), FA = FB = 610 N. Figure B 0.4 m FA FB A 0.3 m Part A Determine the couple moment acting on the pipe assembly and express the result as a Cartesian vector. Enter the x, y and z components of the couple moment separated by commas. Express your answers in newton-meters to three significant figures. Mc = Submit Provide Feedback - ΑΣΦ Request Answer ↓↑ vec ? N.m Next >
QUESTION 2 Figure Q2 shows the cross section of a beam. The beam is simply supported over a span of 6 m and carries a vertical point load of 40 kN acting at its midspan. 440 mm 60mm 135 mm 135 mm 60mm 50 mm 320 mm Figure Q2: Cross section of a simply supported beam Calculate: 2.1. The position of the horizontal centroidal axis of the cross-section from its bottom. 2.2. The second moment area of the cross-section about the horizontal centroidal axis 2.3. The maximum shear load per unit length (metre) at the lower surface of the top flange 300 mm 50 mms0 "50 mm
Consider the beam shown in Figure 2 (a) with the cross-section shown in figure 2 (b). a) Determine the reactions, bending moment and shear force along the beam AD and sketch the corresponding diagrams, 2 kN/m В 400 mm 工 130 mm 1.5 m 400 mm 20 mm 180 mm -2 m .1 m (а) (b)
A horizontal force F shown in the figure is exerted on a vertical lever to prevent a load (weight W) from falling downwards. The drum can rotate without friction about point B; the coefficient of static friction between the drum and the block is μ0=0.30. Determine the magnitude of the force F (in kN) needed to prevent the drum from rotating. a= 4mb=3mc=1mdiameter of the drum = 4m
The structure ABCD given in the following figure is designed to support a finite mass hanging from a cable, DF, attached to the structure at point D. where x = 3 m, y = 3 m, and z = 4 m. The structure is mounted to the ground by a hinge at B and a roller at C and is also supported by a horizontal cable, AE, attached to the wall. The mass of the object hanging from cable DF is 204 kg. The tension in the support cable AE is 1000 N. Determine the force in each member and the reaction forces. A E D
Consider the compound beam shown in (Figure 1). Assume C is a roller, B is a pin, and A is fixed. Suppose that w = 16.5 kN/m Figure 3 m B 6 m < 1 of 1 Determine the moment of reaction at A. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. MA = Submit Part D • Nc = μA 1 D Value Request Answer Determine the normal reaction at the support C. Express your answer to three significant figures and include the appropriate units. μA Value Units 1 @ Units Review ? Your device needs to restart to install update