The block shown in (Figure 1) has a mass of m =90 kg, a height H = 1.8 m, and width L = 2.4 m.It is resting on a ramp that makes an angle = 23°with the horizontal. A force P is applied parallel tothe surface of the ramp at the top of the block.What is the maximum force that can be appliedwithout causing the block to move? The coefficientof static friction is us = 0.41, and the center ofmass of the block is at the center of the rectangle.Figure8H<1 of 2Part DUse the free-body diagram shown in (Figure 2) and write the equilibrium equation for the moments about the point of contact.Express your answer in terms of one or more of P, W, H, L, N, F, and 0.Σ Μo = 0 =Submit Request AnswerPart EPtipSubmitWhat is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip?Express your answer to three significant figures with appropriate units.Part FPmax =SubmitΑΣΦValueProvide FeedbackRequest AnswerValue↓↑What is the maximum magnitude of P that does not cause motion of the block?Express your answer to three significant figures with appropriate units.vecRequest AnswerUnits?Units?

mass of block (m) = 90 kgheight (H) = 1.8 mlength (L) = 2.4 mcoefficient of friction () = 0.41need…

What is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip? Express your answer to three significant figures with appropriate units. Ptip = Value Submit Part F Request Answer Pmax Units What is the maximum magnitude of P that does not cause motion of the block? Express your answer to three significant figures with appropriate units. Value ? Units ?

What is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip? Express your answer to three significant figures with appropriate units. Ptip = Value Submit Part F Request Answer Pmax Units What is the maximum magnitude of P that does not cause motion of the block? Express your answer to three significant figures with appropriate units. Value ? Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q_24. Refer to Table 12.6 and Figure 12.12 attached. What would be the fatigue damage according to…

A: Given: Maximum repetitions, N = 50,000 Single axle load = 26-kip Subgrade, k = 200 psi/in Flexural…

Q: 24. Refer to Table 12.6 and Figure 12.12 attached. What would be the fatigue damage according to the…

A: Repetitions- 50,000 single axle -26 kip subgrade(k) = 200 psi/in flexural strength or modulus of…

Q: Find fr (modulous of rupture) = ? M, bending moment = ? k = ? j = ? y = ? I = ? 0

Q: If the bucket and its contents have a total weight of 191lb, determine the force in the supporting…

Q: 1. For the loads given below, calculate the highest load combination. State which load case governs…

A: Given:- The magnitude of the dead load = D = 2.8 kPa The magnitude of the live load = L = 1.9 kPa…

Q: Figure P- 4.5 ft 1.5 ft 1.5 ft A 2.5 ft + 3.5 ft Part B Determine the maximum force P that can be…

Q: A 1 in diameter rod decreases in length by 0.001 inches when subjected to a 4,893 kip load. If the…

A: Diameter of the rod (d) = 1in. Decreases length of the rod (∆L) = 0.001 in. Load (P) = 4893 Kips Rod…

Q: The following strains were measured using a 0-45-90 degree rosette, with the 0 degree strain gauge…

Q: 4.5 ft 1515ft T 2.5 ft 3.5 ft Part B occurs Determine the maximum force P that can be applied…

A: Given: Crate load = 330 lb Coefficient of static friction, μs=0.45 Tipping also occurs To find: The…

Q: For the beam shown, the magnitude of the concentrated load is P = 11 kN, the magnitude of the couple…

Q: A cement grinding mill "A" with a capacity of 50 tons per hour employs P12,000 per ton…

A: Solution-

Q: A 1 in diameter rod decreases in length by 0.007 inches when subjected to a 2,571 kip load. If the…

Q: Express your answer to two significant figures and include the appropriate units. HA FDA Value Units…

A: Given:- W=16lb To find:- FDA FDB

Q: The aggregate used in road construction begins degrading integrity of said roadway when pieces begin…

A: The mean of aggregate = 19mm The standard deviation = 5.5mm The aggregate in road construction =…

Q: In (Figure 1), k = 180 N/m. Figure Tc- 2 m- -3 m- wwwww 1 of 1 > Part A Determine the unstretched…

A: Mass of the crate = m= 40kgSpring constant= k = 180N/mFree body diagram:-

Question

The block shown in (Figure 1) has a mass of m =
90 kg, a height H = 1.8 m, and width L = 2.4 m.
It is resting on a ramp that makes an angle = 23°
with the horizontal. A force P is applied parallel to
the surface of the ramp at the top of the block.
What is the maximum force that can be applied
without causing the block to move? The coefficient
of static friction is us = 0.41, and the center of
mass of the block is at the center of the rectangle.
Figure
8
H
<
1 of 2
Part D
Use the free-body diagram shown in (Figure 2) and write the equilibrium equation for the moments about the point of contact.
Express your answer in terms of one or more of P, W, H, L, N, F, and 0.
Σ Μo = 0 =
Submit Request Answer
Part E
Ptip
Submit
What is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip?
Express your answer to three significant figures with appropriate units.
Part F
Pmax =
Submit
ΑΣΦ
Value
Provide Feedback
Request Answer
Value
↓↑
What is the maximum magnitude of P that does not cause motion of the block?
Express your answer to three significant figures with appropriate units.
vec
Request Answer
Units
?
Units
?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: free body diagram and forces components

VIEW

Step 3: maximum magnitude of P before tipping calculation

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure A 4.5 m Wo B. 1 of 1 1.5 m C Part A Determine the largest intensity wo of the distributed load that the beam can support if the beam can withstand a maximum bending moment of Mmax = 12 kNm and a maximum shear force of Vmax = 80 kN. (Figure 1) Express your answer with the appropriate units. Wo = Submit ☐ O µA Value Request Answer Return to Assignment Units Provide Feedback
What is the Volume of the Dump Truck Bed? 7'2" = 86" 5' 60" 19 = 228" IN FEDT A₁ = 7'2"=5 - (7-1)(5) = 35.834* V. = (35.83 +¹) (14') = 680.83 Ft ³ A₂ = 15h = 12/2₂ (0.5) (0.5) = 0.125 1² V₂ = (0.125 +6²) (19¹) = 2.375 ft² V TOTAL = V₁ V₂ -V₂ = 68c 83 Ft² - 2.375 PL³-2.375 F6³ A₁ = 86" x 60" = = 5160 IN ² V₁ = (5160 N) (2284²) = (176480 IN ³ A₂ = (2) (6) (6²) = 18 N² V₂ = (18+) (228 (N²) = 4104 IN ³ TOTAL = 117648014³ - 4104 IN³ - 410414³ TO GET INTO CF YOU WOULD DIVIDE BY 1728.
1. For the loads given below, calculate the highest load combination. State which load case governs and the clause used. D = 2.8 kPa L= 1.9 kPa S = 3.13 kPa W= 0.9 kPa E = 1.1 kPa
Thank you for explaining in advance
The following diagram shows a partial floor framing plan of an elevated walkway building connecting an airport terminal building to the adjacent garage. The concrete floor is not post- tensioned. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Framing members are not exposed to weather or in contact with soil. Per the ACI, what is the minimum slab depth? Consider both the interior slab and the cantilevered slab at the edge of the building. 30-0¹ B4 B4 B4 83 Column 52 SI 30-0 -Sab Mark Dean- B4 B4 B4 83 B 30-0¹ BI B2 B2 BI -Girder 12 A 1 3-4 Ei 13:4 05 40-0 to 2