velocity of the collar is 0.1 m/s. The spring attached to the collar has an undeflected length of 10 cm and a constant of 3 N/m. Calculate the distance x of position 2, where the collar will come to a stop. A 2-kg collar slides without friction along a horizontal rod as shown. At the position 1, the 20 cm- Vi= 0.1 m/s ww x = ? ww 2.

velocity of the collar is 0.1 m/s. The spring attached to the collar has an undeflected length of 10 cm and a constant of 3 N/m. Calculate the distance x of position 2, where the collar will come to a stop. A 2-kg collar slides without friction along a horizontal rod as shown. At the position 1, the 20 cm- Vi= 0.1 m/s ww x = ? ww 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete beam has a width of 400mm and an effective depth of 600mm. It is reinforced for tension with 4-28mm rebars. F'c = 20.7MP and Fy = 414.6MPa. 7. Determine the ultimate moment capacity. a 484.76KN.m b. 448.67KN.m 8. Determine the percent increase in ultimate b. 34.4% a. 25.1% c. 487.46KN.m d. 446.87KN.m moment if depth is increase to 700mm. c. 18.98% 15.68%
statics of rigid bodies
statics of rigid bodies
Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over a 5m. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block. 7m 5m 10m
The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown, determine the mass of the block at D. Give your answer in kg and to 3 significant figures. 3 m- 3 m www. KAC = 20 N/m -4 m- www wwwww B KAB = 30 N/m
The figure shows a sphere resting in a smooth Vshaped groove and subjected to a spring force. The spring is compressed to a length of 125 mm from its free length of 150 mm. If the stiffness of spring k= 10 N/mm and weight of sphere is 100 N. Determine the contact reactions at the point A and B. 30° eeee • W 60° 1
The three identical bars, each weighing 10.8 lb, are connected by the two freely pinned links of negligible weight and are resting on a smooth horizontal surface. Calculate the initial acceleration a of the center of the middle bar when the 7.8-lb force is applied to the connecting link as shown. 7.8 lb Answer: a = i ft/sec2
2. A 1.25-kg block was released from the rest position at A by a compressed spring (k = 100 N/m). The coefficient of kinetic friction between the block and the floor is k = 0.25. The uncompressed length of the spring is 1 m. The curved ramp from B to C is frictionless and the block loses contact with the ramp after passing point C. The path of the block is represented by a broken line. Determine (a) the velocity of the block at points B and C. Also, calculate (b) the normal force at point C just before the block left the ramp. (VB = 0.3082 m/s →, Vc = 3.4041 m/s 45°, N = 1.4285 N 71 45⁰) 0.75 m A 1 m B 2 m O 45⁰ 2 m G
Beam determine the support reactions (solve using integral)
Mass of forklift: 1,000 kg Mass of crate: 750 kg The driver is raising the crate at 2 m/s². Determine the reactions at A and B (in Newtons). 0.5 m -1 attachment 0.4 m
calculate the reactions using static equilibrium Please show all steps + FBD You should use TwO FBDS! w = 1.0 kip/ft 14 ft 10 ft 45 deg D 24 ft
Question A mild steel bar, circular in cross-section, tapers from 40 mm diameter to 20 mm diameter over its length of 800 mm. It is subjected to an axial pull of 20 kN. E = 2 x 105 N/mm². The increase in the length of the rod will be