The beam of negligible weight is supported horizontally bytwo springs. The beam is horizontal and the springs areunstretched when the load is removed. Suppose thatk₁=1.5 kN/m and ka 2.6 kN/m (Egure 1)Figure600 N/m3 m1 of 1DYPart ADetermine the angle of tit of the beam when the load is appliedExpress your answer using three significant figures.Η ΑΣΦ0=SubmitProvide FeedbackRequest Answervec 5I

Objective: To determine the angle of tilt of the loaded beam. Given: Spring constant of spring at…

The beam of negligible weight is supported horizontally by two springs. The beam is horizontal and the springs are unstretched when the load is removed Suppose that kA 1.5 kN/m and ku 26 kN/m (Egure 1) Figure www 3 m 600 N/m 3m 1 of 1 D Part A Determine the angle of tit of the bear when the load is applied Express your answer using three significant figures. [90] ΑΣΦ) 0 Submit Provide Feedback Ivec Request Answer I

The beam of negligible weight is supported horizontally by two springs. The beam is horizontal and the springs are unstretched when the load is removed Suppose that kA 1.5 kN/m and ku 26 kN/m (Egure 1) Figure www 3 m 600 N/m 3m 1 of 1 D Part A Determine the angle of tit of the bear when the load is applied Express your answer using three significant figures. [90] ΑΣΦ) 0 Submit Provide Feedback Ivec Request Answer I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.6 kN when 0 = 32°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 90 mm, b = 550 mm. T₁ Answers: P= i T₂ = i 4 a B A kN kN 0000000 T₂ P
F A The wagon has a mass of 19.5 kg and centre of mass at G. Both the front and rear wheels are locked, meaning the wheels will not roll. Take u, - 0.25 a- 0.300 m, b - 0.400 m, c - 0.500 m and d 0.750 m What is the normal force acting at A digits. answer in N using 3 significant What is the normal force acting at B digits. answer in N using 3 significant What is the frictional force acting at A digits. answer in N using 3 significant
asnwer correctly
Find the maximum moment of the given load train at point n on the beam given in the figure?(Single load and distributed load train move on the beam. (a=4 m between n-A, b=8 m between n-B)
Determine the maximum value of b (lb/ft) if the roller at point A can only support upto 105 lb. The beam is 16 ft long while c=6.7 ft and a=3.4 ft. Round off only on the final answer expressed in 3 decimals.
10
The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.4 kN when 0 = 28°, determine the force P required on the lever and the corresponding tension T2 for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 400 mm. T₁ Answers: P= T₂ = i Al kN kN b [000000 T2
Use Use x = 137 y = 37 a = 6 b = 8 c = 1 answer number 20 and 21 only
RAH RBH C SF TRBV 500 600 200 E RAH RAV RDH 120 RDV 2. Each member of the frame shown in the figure weighs 50 KN/m. Compute the horizontal and vertical components of the pin pressure at C, D and F. blem n ma In the ction
A continuous beam is supported by a spring at D with spring constant of 40kN/m as shown. Determine the reactions at the supports A and B and the spring force and draw the bending moment diagram. Given E=200GPa, I=4×107mm4 . (Hint : take the spring force as unknown).
A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar BC is 2.4 m. a. Draw the FBD of the circular cylinder and the bar BC.b. Determine the tension in the cord CD.
The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0 = 31°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 90 mm, b = 590 mm. T₁ Answers: P= i T₂ = Mi a A B kN KN b bo 1000000 T2 P