e2-lb spool slides along the smooth horizontal spiral rod, r = (20) ft, where is in lians, as shown in (Figure 1). At the instant = 90°, its angular rate of rotation is stant and equals Ⓒ = 4 rad/s. re 1 of 1 Determine the horizontal tangential force P needed to cause the motion. Express your answer in pounds to three significant figures. VAX vec? Submit Part B Submit Request Answer Determine the horizontal normal force component that the spool exerts on the rod. Express your answer in pounds to three significant figures. ΠΠ ΑΣΦΠ Pec Provide Feedback Request Answer lb (? lb

e2-lb spool slides along the smooth horizontal spiral rod, r = (20) ft, where is in lians, as shown in (Figure 1). At the instant = 90°, its angular rate of rotation is stant and equals Ⓒ = 4 rad/s. re 1 of 1 Determine the horizontal tangential force P needed to cause the motion. Express your answer in pounds to three significant figures. VAX vec? Submit Part B Submit Request Answer Determine the horizontal normal force component that the spool exerts on the rod. Express your answer in pounds to three significant figures. ΠΠ ΑΣΦΠ Pec Provide Feedback Request Answer lb (? lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A T₁ Co B S T₂ C L₂ T3 L3 T4 O The image above shows a solid shaft with various torques applied in the directions shown. The values for each torque are as follows: T₁ = 800 N•m, T₂ = 600 N.m, T3 = 400 N·m, and T4 = 200 N·m. The values for the maximum shear stress in each section are as follows: TAB = 75 MPa, TBC = 90 MPa, and TCD = 100 MPa. Find the minimum allowable shaft diameter.
Solve it asap pl
ASAP, if you cannot answer it please reject it.
Example: Determine the resultant of the three tension forces acting on the eye bolt. 30 4 kN 20 KN 8 kN
Solve using Mohr circle method
Help me figure out the problem. Asking for the moment diagram? and then, Show the value of x knowing you have the shear diagram. Again find the moment diagram and the value of your x. Show complete solution and box the final answer and write on a paper.
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
Please answer soon
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and B. (b) Draw the shear-force and bending-moment diagrams for the beam. (c) Determine the deflection in the middle of the span. Assume w = 11 kN, L = 7.4 m and El - 6.9 x 104 kN-m2 is constant for the beam. V. L.
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Q3: Figure (3) shows a punching machine of plate (thickness 2 mm).Punching operation is applying many times to make thousands holes (d-4 mm) through cam (2) which attaches with the ram (1) from two sides and moves it up and lowering down by action of weight (1000N). Assume the ram (1) is circular cross section. Requirement: Select the correct answer of following: 1. The ram (1) subjected to static bending stress at section (X-X): 1800ND Flgure (3) X- B. 100 mm A: True B: False 2. The ram (1) subjected to reversed load at section (Y-Y): B. False 3. The diameter of ram (1) at section (X-X) is (44603 mm): B: False 1- A: True A: True 4. The diameter of ram (1) al section (Y-Y) is (9.694 mm): B: False A: True For ram (1) and pin (b): S,-160 MPa S,-210MPA S-100MPA 5. The torque required to rotate cam (2) is (10000 N.mm): A: True B: False 6. The plate material can be punched by this mechanism has (S,-39.788 MPa): N= 2.5 A: True 7. The diameter of pin (b) on the ram (1) is (6.307 mm): B: False…
02) The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmax = 1936x(0.5). 2. IfG =30 GPa find the angle of twist at the free end of beam. Y 10 kN 25 NA 120 mm 15 500 mm Good Luck and be Green