n W or = 3.35 The electric motor exerts a 500 Nm-torque on the aluminum shaft ABCD when it is rotating at a constant speed. Knowing that G 27 GPa and that the torques exerted on pulleys B and C are as shown, determine the angle of twist between (a) B and C, (b) B and D. 200 Nm Fia. P3.35 B 40 mm 300 Nm 44 mm 1 m 48 mm 1.2 m Search 0.9 m

n W or = 3.35 The electric motor exerts a 500 Nm-torque on the aluminum shaft ABCD when it is rotating at a constant speed. Knowing that G 27 GPa and that the torques exerted on pulleys B and C are as shown, determine the angle of twist between (a) B and C, (b) B and D. 200 Nm Fia. P3.35 B 40 mm 300 Nm 44 mm 1 m 48 mm 1.2 m Search 0.9 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2/77 The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N•mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. F = 4 N 10 mm 15° A 40 mm 300 N•mm Problem 2/77
EXAMPLE 4.7 Two cylindrical rods, one of steel and the other of brass, are joined at Cand restrained by rigid supports at A and E. For the loading shown and knowing that E.= 200 GPa and E.= 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm 100 100 -180 -15 Dl Вгass 40 kN E Steel B. 60 kN 40-mm diam. 30-mm diam.
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
B10
350 mm 25 mm 40 mm Q11. Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E, = 200 GPa and E, = 105 GPa, determine а. the reactions at A and E. b. the deflection of point C. Dimensions in mm 180- 100 -120-- 100 Cl DI E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam. pla 6 k Q12. In a standard tensile test of a steel rod of 22-mm diameter is subjected to a tension force of 75 kN. Knowing that v = 0.3 and E = 200 GPa, determine the elongation of the rod in a 200-mm gage length. b. the change in diameter of the rod. dec mm mod a. mate
CLO 3: An 8-m simply supported beam AB carries a downward 8- kN point load located 6 m from the left support A. Determine the value of constant of integration, c2. -35/EI -40/EI -20/EI
A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the shaft deflection at point C. Assume that the bearing at point A can be idealized as a pin support and the bearing at point E can be idealized as a roller support. ... A B D E C 300 mm 200 mm 300 mm 200 mm 750 N 500 N (A -1.101 mm -0.936 mm -0.876 mm D) -1.586 mm E) -0.697 mm
The shaft is connected to a generator at A and the torque applied at each of the four gears is as follows: Tu = 40 N.m. T. = 25 N.m. T, 34.5 N.m. T, 23 Nm. The shaft is made of Aluminum 2014-T6 and H has a polar moment of inertia J= 2 *10 m. Find the angle of twist of gear E with respect to gear D knowing that the distance between the two gears is 840 mm. O0.0537 rad O0.0358 rad 10.0132 rad O 0.933 rad 40.0179 rad
2) The box beam is constructed from four boards that are fastened together using nails spaced along the beam every 2 inches. The beam is subjected to a maximum internal shear force of 475 lb. a) Locate the neutral axis and compute the moment of inertia for the cross-section in in*. [Ans. to check: 1 = 197.7 in¹] b) Calculate the first moment of area in in³ at each of the two connection interfaces (i.e. once for the top flange and once for the bottom board). Draw a clear sketch of the cross-section showing the neutral axis and the necessary dimensions to calculate the first moment of area. [Ans. to Check: Qtop = 31.2 in³] c) Compute the shear flow occurring between the wood and the nails at each of the two connection interfaces in lb/in. [Ans. to Check: qbottom = 49.0 lb/in] d) Design the section by choosing the required shear strength of the nails (in lb). Check both interfaces but choose only one assuming you would like to use the same nails for the entire beam. [Ans. to check: 75 lb…
Please help. I'm not sure why the answer is 910?
A rectangular column with cross-sectional dimen- sions b and h is pin-supported at ends A and C (see figure). At midheight, the column is restrained in the plane of the figure but is free to deflect perpendicular to the plane of the figure. Determine the ratio h/b such that the critical load is the same for buckling in the two principal planes of the column. CO L Ix 2 B Soati
The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a clockwise moment of 120 N-m is needed to tighten the nut at A and the extension d = 300 mm, determine magnitude of force F required to develop this the moment. A 300 mm 30° 15⁰° F