QI: A horizontal rectangular channel of constant cross section has a sluice gat. When the gate is partially opened, water flow at 6 m/sec. with a depth of 60 cm. Determine whether a hydraulic jump will occur, and if so, which type is it? How much its height (Dz-Di) and find the head loss through it? D 1 + 8Fr,2 - 1 D,

QI: A horizontal rectangular channel of constant cross section has a sluice gat. When the gate is partially opened, water flow at 6 m/sec. with a depth of 60 cm. Determine whether a hydraulic jump will occur, and if so, which type is it? How much its height (Dz-Di) and find the head loss through it? D 1 + 8Fr,2 - 1 D,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin 3-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 3-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Assume w = 3 ft, D= 3 ft, L = 3 ft. Width = w Right-angle gate. Hinge Water D
Solve C only; subject: Hy
1. Water is flowing with velocity 2.8 m/s in an 80 mm diameter half opened gate valve. Determine the head loss through this valve. (Ans.: 2.398 m)
1. (Flow rate problem) Water at 50°F flowing through 80 ft of 4-in-diameter average cast-iron pipe (e = 0.00085 ft) causes a friction head loss of 0.27 ft. Find the flow rate.
A- A regulator with discharge = 22m 3 /sec , rounded entrance is used for piers and abutment , water level at flood time =92.8 , bed level=90.3m at u/s, D/s water level = 92.2m.Bed level under gate= 9lm. Decide the flow condition after the gate when it is opened partially (free or submerged), then find the value of partial opening. no of piers =2, each one has thickness lm.
A 60cm square gate has its top edge 12m below the water surface. It is on a 45deg angle and its bottom edge is hinged. What is the total hydrostatic force acting on the gate? Select the correct response:
Q3/ Three opening of head regulator with 2 m each. The head between US and DS equals to 1.75 m. and the vertical opening of the gates is 2.5 m. if the water in the DS decreases by 0.25 m. Use cd as 0.62 and find the following: a- the vertical gate opening required to maintain the same amount of the discharge if the water level in the D/S decreases by 0.25 m b- the vertical gate opening required to maintain the same amount of the discharge if the water level in the U/S and D/S rise by 0.5 m
For the sluice gate shown, if Cv=0.90 what is the flow rate? If Cc=0.71 what is the height of the opening?
Water is flowing in the spillway chute with a discharge of 150m^3/s which has a rectangular section and is 15m as shown. n=0.015. a.) What is the depth of flow at the bottom of the 3% slope at A? b.) What would be the required depth of tailwater at section B to cause a hydraulic jump to cause a hydraulicjump to form on the flat slope? c.) Determine the horsepower degenerated due to the jump?
Draw the flow nets under an impermeable dam.
A thin 6-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Width 6ft- Right-angle gate Hinge 39000 0. 4 ft Water 2ft-diameter pipe
*12-4. A rectangular channel has a width of 2 m. If the flow is 5 m/s, determine the Froude number when the water depth is 1.5 m. At this depth, is the flow subcritical or supercritical? Also, what is the critical speed of the flow?