A thin 5-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure b The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Assume w-5 ft, D-2 ft, L-2 ft. ft Width w Right-angle gate. Hinge. Water

A thin 5-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure b The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Assume w-5 ft, D-2 ft, L-2 ft. ft Width w Right-angle gate. Hinge. Water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three riveted steel pipes (e = 0.006 ft) are connected in series. Find the flow throughthem if the pipe diameters and lengths are D1: 24 in, D2: 18 in, D3: 20 in, L1: 1500 ft, L2:1600 ft, and L3: 2000 ft and the total head loss of the system is 145 ft. Use the DarcyWeisbach equation and assume complete turbulence. Minor losses (entrance, exit, etc.) shallbe considered.• Determine f for each pipe from Figure 6.9 or Moody Diagram.• Attached the diagram that is used to find f’s and show your work on the diagram;and• Assume both expansion and contraction have an angle of  = 40
Determine the equivalent length pipe with a diameter of 300mm and a C value of 100 that will replace the arrangement from A to C below. A 800m, 4000, C=90 1600m, 3000, C=110 1400m, 2000, C=95 C D
A thin 3-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 3-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Assume w = 3 ft, D= 3 ft, L = 3 ft. Width = w Right-angle gate. Hinge Water D
Q1: Find the discharge through the pipe if The diameters of sections (1) and (2) are 25 cm and 30 cm respectively. The velocity of water at section (1) is 6 m/s. Determine also the velocity at section (2) D- 3ecm D25 cm 6m/s
For the hydraulic structure shown below check the thickness of the floor at points (A) and (B) by using Lane's method, and then check the structure against piping use (C-5). vertical gate Flow 109,9 106.5 0/5 F5L-112.2 100.5 05 - 240 (1) 110.0 all Dimensions in meter 09 108,5 0.5 (2) 107.9 106.1
Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2 ) of the pipe are considered. The diameter of the pipe at section 1 is (200 + 33 ) mm and (120 + 33 ) mm at section 2. The elevations of the sections 1 and 2 above datum are (800 + 33) cm and (400 + 33 ) cm respectively. If the pressure at section 1 is 40x104 N/m? and the discharge through the pipe is 60 litres per second, calculate the intensity of pressure at section 2. /
Water (p = 1000 kg/m³) flows horizontally through a nozzle into the atmosphere under the conditions given below. (assume steady state flow). Nozzle Water 2 O A2, V₂, P₂ A₁, V₁, P₁ At inlet: A₁ = 10-3m²; V₁ = 2m/sec; P₁ = 3 x 105 Pa (gauge) At outlet: A₁ = 10-4 m²; P2 = Patm Determine the external horizontal force needed to keep the nozzle in place.
Water is flowing steadily in a horizontal elbow and nozzle combination shown in the figure. The gage pressure at section (1) is 100 kPa with inlet velocity of 2 m/s. At section (2) the water exits to the atmosphere. Neglecting pipe weight, determine the magnitude and direction of the x and y components reaction forces exerted on the flanges to withstand this flow. 160 mm y section (2) 300 mm V1 -> section (1) P, = 100kPa V, = 2m/s
... "H" hinge water A 1m 40KN 1.5m In the figure shown, find the depth of water "H" if the force at the bottom of the gate is 40KN to make the system equilibrium. The rectangular gate which is hinged at point A has a dimension of 1m depth and 1.5m width. A) 5.77 m B 6.27m 5.27 m No answer among the choices E 6.77 m
A thin 6-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Width 6ft- Right-angle gate Hinge 39000 0. 4 ft Water 2ft-diameter pipe
A triangular gate having dimensions shown is hinged at its top at A. The gate rests on a frictionless surface at B. A.) Determine the hydrostatic force acting on the gate. B.) At what distancce from the centroiid of the panel is the hydrostatic force acting?