Answer the following with (True) or (False): 1- A siphon is a closed conduit designed to run partially full and under presser flow. 2- Pipe sections are used for large culverts to pass the flow under an obstruction. 3- Rupture of floor due to suction caused by local scouring. 4- In the gate design, the plate considered as a slab simply supported on tow beams. 5- The depth of water corresponding to the min. specific energy is known as critical depth.

Answer the following with (True) or (False): 1- A siphon is a closed conduit designed to run partially full and under presser flow. 2- Pipe sections are used for large culverts to pass the flow under an obstruction. 3- Rupture of floor due to suction caused by local scouring. 4- In the gate design, the plate considered as a slab simply supported on tow beams. 5- The depth of water corresponding to the min. specific energy is known as critical depth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.
1. The total headlost from A to E as shown is 20 m. Use n = 0.011 to all pipes Compute for the discharge at line 2 Compute for the discharge at line 1 Compute for the discharge at line 4 (BCD) Pipe Diameter Length in (mm) 600 AB BC CD BD DE 450 450 500 600 Q1 = Q3 Q1 = Q2 + Q4 hfr = hf₁ + hf₂ + hf3 hf₂ = hf Q4 = 0.2974 m³/s Q₁ = 0.7663 m³/s Q3 = 0.7663 m³/s Q2 = 0.4689 m³/s m 600 400 450 600 650 1 B 2 C D 3 E
Check the hydraulic structure shown below against piping and then find the thickness of floor at point (B) by using uplift pressure diagram (Use Bligh's theory for solution). u/s max. w.s.l-103.4m d/s max. w.s.l-100.2m - Vertical gate flow ws mim. w.s.l101,6m d/s mim, w.s.l-97.6m 6 m 8 m 10 m 18 m 22 m
Please help with solving A,B,C
14. the flow rate in pipe with diamiter 115mm and the flow is turbulent .the kinematic velocity=D1.15* 10^-6 will be 2.076*10^-4 O 4.156*10^-4 15. The type of flow if the flowrate is 0.1 I/s.the diamiter is 100 mm.the kinematic viscocity=D1.003*10^-6 is TURBULENT O LAMINAR 16.if the flow rate is 1.5 and the flow is laminar.viscocity is 1.003*10^-6. The diamiter will be 476mm true false K
Problem 2 Ans:(a) 110.28MPA, 22.5MPA, 98.22MP3; -58.09MPA, 22.5MPA, -100.9MPA (b) 1.115, 1.104; (c) 1.213, 1.270 A pipe with an outside diameter of 140 mm and a wall thickness of 7 mm is subjected to the 16-kN load shown in figure a. The internal pressure in the pipe is 2.50 MPa, and the yield strength of the steel is oy 240 MPa. (a) calculate and show combined stress state on two separate stress elements: one for point Hand one for point K (b) determine the factors of safety predicted at points H and K by the maximum-shear-stress theory of failure (c) determine the factors of safety at points H and K predicted by the maximum-distortion-energy theory (d) on common or separate axis draw the stress envelope(s) (failure diagram(s)) for both theories indicating all stress values as well as the load line(s). figure (a) 700 mm I0 mm 16 AN
Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a pipe BC which is 60" in diameter. At C the pipe forks. Branch CD is 32" in diameter and carries one-third of the flow in AB. The velocity in branch CE is 8fps. (a) Find the the diameter of CE in inches.
1- from problem on F5-7, Water flows through the 80-mm diameter pipe, head loss from A to B is hu = 0.5 m. Set datum, z = 0, at point B. Do the following: %3D (A) List the boundary conditions for location A and B. (B) Compute the flowrate in the pipe (C) Compute the height of Energy Grade Line (EGL) at point B A 6 m VB B
the marked choice is the correct answer.
The pipes in a portion of a water Works system as shown consist of the following: Section AB -5,000 ft. of 8 in. diameter BC - 2,000 ft. of 6 in. diameter CD - 1,000 ft. of 8 in. diameter BE - 2,000 ft. of 8 in. diameter EC - 1,500 ft. of 7 in. diameter If the total loss of head due to friction from A to D is 12.6 ft., what is the discharge in Section CD in cfs? Use the Darcy Weisbach formula with f = 0.02. round your answers in 3 decimal places
Hello could you please provide the full workings out for this past paper question. Correct answers are circled
choose the correct multiple-choice answer and also show your work): The Darcy friction factor in Branch b in the figure below is 0.025 and the turbulent friction factor in Branch b is 0.021. If this 0.1342-ft ID pipe is 16ft long, determine the head loss in Branch b in terms of ??2.The elbows are 90°long radius. Neglect losses in the junctions.