Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a pipe BC which is 60" in diameter. At C the pipe forks. Branch CD is 32" in diameter and carries one-third of the flow in AB. The velocity in branch CE is 8fps. (a) Find the the diameter of CE in inches.

Q: QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a…

A:

Q: Two pipes 1 and 2 of the same length and diameter are connected in parallel. If f2 = 0.914f1, the…

A: solution Given we know hf=flv2d×2g=flQ212.1d5given f2=0.914f1as the pipes are parallel the head loss…

Q: - A pipe has what is the

A:

Q: 4) The increase of temperature results in (a) increase in viscosity of gas (d) decrease in viscosity…

A: The Bernoulli equation states that, points 1 and 2 lie on a streamline, the fluid has constant…

Q: 1. Gasoline (sp. gr. 0.8) is flowing upwards a 150 mm vertical pipeline which tapers from 300 mm to…

A: To find (a) Differential guage reading (b)Rate of flow

Q: Which of the following is a valid potential function for incompressible flow? (Assume A is numerical…

A:

Q: 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines…

A:

Q: A fluid of constant density flows at the rate of 15 li/sec along a pipe AB of 100-mm-diameter. This…

A:

Q: Oil (SG = 0.86) is passing through a horizontal pipe whose diameter increases from 150mm diameter at…

A: Given:- specific gravity of oil = 0.86   Diameter at section 1= 150mm = 0.150m Diameter at section…

Q: The water tank shown below is being filled through section 1 and maintained at level h =5m. The flow…

A: Given data in question  Depth Water  Diameter  To find out  Velocity V1

Q: In a pipeline of diameter 'd there is a large number of laterals tapping uniformly at the average…

A: Given data: Diameter=d Discharge at entrance=Q Length=l It is required to prove the head loss due to…

Q: For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per…

A:

Q: The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B D O There is a…

A:

Q: This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The…

A:

Q: PROBLEM 03: Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes…

A:

Q: 6. Determine the flow rate and the velocity in each pipe if 4 of the flow goes into pipe 2 with a…

A:

Q: The four pipes below have steady flow of an incompressible, ideal fluid with density ps. The…

A: Four manometers are given with the three pairs of options

Q: Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow…

A:

Q: In a horizontal 5-inch pipe (ID = 5 in.), water is being delivered at a stable discharge of 25…

A:

Q: Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 cfs. What is…

A:

Q: Water flows from tank A to tank E as shown in the figure. The head loss from B to C is 9 times the…

A: Compute: A. What is the discharge in m³/s? = B. What is the velocity in the 150 mm diameter…

Q: Fluid flows at the rate of 0.272 m/s in a 925 mm diameter pipeline 588 m. long. Specific gravity of…

A: V = 0.272 m/s D = 925 mm or 0.925 mL = 588 m f = 0.012

Q: A 1 B 3 D 5 E 2 C Pipe | Length Diameter 600 m f 1 600 mm 0.025 600 m 900 m 500 m 300 m 460 mm 300…

A:

Q: A Pipe 1 2 3 L(m) 120 180 60 D₁-8 cm -0.0288 20.0260 -0.0314 D₁-6 cm Three pipes are in parallel…

A:

Q: 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines…

A: As per company policy we can only answer first three questions. Kindly post the other question as…

Q: 1. A pipe of diameter 1.1 ft narrows to a diameter of 0.8 ft. Air moves through the pipe at a mass…

A: given mass flow rate,  m. = 6.1 Pressure and temperature at section 1 P1 = 110 + 14.7 = 124.7 psia…

Q: Q1) Mott recommends the following formula for the friction head loss hf, for flow through a pipe of…

A: Given data Frictional head loss = hf Length of the pipe = L Diameter of the pipe = D Volume flow…

Q: 4 A 25 cm diameter pipe carries oil of sp. gr. 0.9 at a velocity of 3 m/s. At another section the…

A: Given: Diameter 1, D1 = 25 cm = 0.25 m Diameter 2, D2 = 20 cm = 0.2 m Specific gravity = 0.9…

Q: 2. A discharge of 8.5 L/s of oil having a sg=0.8 occurs through the venturi shown. The diameter of…

A:

Q: 2. The total flow from A to E is 300 L/s. Compute the flow for pipes 2, 3, 4, and 5 3 5 D 6 Pipe 1 2…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.