QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a diameter of 10". What is the velocity at each section? Section 1= 5.89 ft/sec Section 2= 9.2 ft/sec Section 1- 8.9 ft/sec Section 2= 6.0 ft/sec Section 1= 9.9 ft/sec Section 2- 9.9 ft/sec Section 1- 4.89 ft/sec Section 2= 6.58 ft/sec

QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a diameter of 10". What is the velocity at each section? Section 1= 5.89 ft/sec Section 2= 9.2 ft/sec Section 1- 8.9 ft/sec Section 2= 6.0 ft/sec Section 1= 9.9 ft/sec Section 2- 9.9 ft/sec Section 1- 4.89 ft/sec Section 2= 6.58 ft/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

... L = 700m 2 4 D = 45cm L = 800m D = 40cm L = 600m L = 700m D = 35cm D = 35cm 1 A L = 700m В D = 40cm L = 1200m D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5 A Q3 = 0.160 cu.m/s B) Q1 = 0.253 cu.m/s 3.
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a pipe BC which is 60" in diameter. At C the pipe forks. Branch CD is 32" in diameter and carries one-third of the flow in AB. The velocity in branch CE is 8fps. (a) Find the the diameter of CE in inches.
Show the complete solution for this equation
2. The flow from pipelines A to F is 300 lit/'s. Using a friction factor of 0.015 for all pipelines and with the properties listed below, compute a. the discharge at B b. the discharge at E c. the discharge at D d. headloss from 1 to 5 A Pipelines A TERREY B C D E 8 Length (m) 350 300 320 1100 550 650 Diameter (cm) 40 25 25 30 20 45
Q4) Water flows through a contraction section as shown. A pressure gage connected between the upstream pipe and throat section sk difference of Ap = 5 kPa. The gasoline velocity in the throat section is V2 = 3 m/s. What is the velocity V1(m/s) in the upstream pipe? V shows a pressure V2 AP
COMPLETE SOLUTION WITH EXPLANATION
do not round off everything plsss
7. Find the equivalent length of pipe 1 to 2 with a diameter of 300mm and the velocity of line C. Use the figure below and neglect minor losses. U 1 Pipes A B 3C A Length 300 m 150 m 250 m B 00 Diameter 300 mm 200 mm 250 mm C 10 m D f 0.020 0.021 0.020
Determine the diameter of steel pipe needed to deliver water (20°C) at a rate of 2 cu. m/s from a reservoir with water surface elevation of 60 m to a reservoir 200 m away with a water surface elevation of 30 m. Assume a squared edge inlet and outlet (k = 1) and no bends in the pipe. Further assume there are two open gate valves in the pipe (k=0.2).
A differential gauge was attached to a venturi meter. The deflection of mercury is 14.3 inches. Assume no headloss. Point B is located at the 6 inches diameter pipe. Point A is located at the 12 inches pipe. Determine the flow rate in ft^3/s. 6 indves 12 inches 143 in
e7