Answered: 7. Find the equivalent length of pipe 1…

7. Find the equivalent length of pipe 1 to 2 with a diameter of 300mm and the velocity of line C. Use the figure below and neglect minor losses.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q. 2 Find the flow rate of water in each pipe and the pressure at point 3. Neglect the minor losses.…

A: Many combinations of pipes are connected in series, parallel, or complex networks. So by writing the…

Q: 8- For the system in figure below, each pipe is 250mm diameter ,1000m length and f=0.015, discharge…

A: For calculating discharge in branched pipes, it is important to know the height of the junction…

Q: 1. A 36 inch diameter pipe is 4000 feet long and has a head loss of 12.7 feet. a. Solve for the…

A: Given data in question Head loss Diameter of pipe Length of pipe Mannings coefficient value To…

Q: PROBLEM 5 Consider a steel pipe of inside diameter of 10.02 in having in it an open globe valve (K =…

A: Given, Diameter of the pipe D =10.02 in =0.835 ft. Length of the pipe L=100 ft. Discharge Q=5…

Q: Calculate the discharge in pipe 3, in m^3/s.

A: Step: 1 Head loss: - In fluid system, energy dissipated due to friction along the hydraulic system…

Q: Water is transported in a pipe, at an average flow rate of Q = 80 L/s. Calculate the pressure…

A: Solution of a part a and part b

Q: A solid steel shaft 4 m long is stressed to 85 MPa when twisted through 4.4°. a. Given that G = 83…

Q: er of

A: According to given data Pipe length = 170 m Diameter = 0.42 m Coefficient of roughness C=…

Q: Q.2. For the pipe network shown in the figure below, find the diameter of pipe (DC) if the head…

A: L = 500 m CHW = 100

Q: Water is flowing through a venturimeter shown. The difference in pressure between A (D = 5cm) and B…

A: Given data in question Diameter Head loss To find out Velocity head at A

Q: Q4. B) Plotting the Energy Gradient Line (EGL) or Total Energy Line(TEL) and Hydraulic Grade Line…

A: Given, V1 = 36 ft/s Hm = 0.25 ft

Q: e right solutio

A: Given Figure Given data A=150mm2 E=180GPa L=4m P=50kN Draw Free body diagram

Q: Water discharges from a large tank through a pipe 40 mm diameter and length of 55 m that is sharp at…

Q: 2. IN THE SYSTEM SHOWN, THE COEFFICIENT OF FRICTION BETWEEN BLOCK A AND THE PLANE IS 0.25. NEGLECT…

Q: (b) If the manometer readings are the same but the oil is replaced by air, what is (P1-P2) now? 280…

Q: L For the figure shown, determine the elevation at c. Use Darcy-Weisbach formula to compute for the…

Q: Draw below and a free body diagram for the whole aysterm shown write three equilibrium equations. A…

A: To Determine Three equilibrium equations and Draw the free body diagram.

Q: What inputs and outputs does a life cycle analysis (LCA) of a material consider?

A: When designing a life cycle analysis (LCA), it is really important that it clearly defines the input…

Q: 2. Using AMM, solve for: a. Ymax (mm) b. OB (rad) in terms of EI. (168 kN) P 20 kN/m A 2 m B 3 m 36…

Q: Include all necessary FBD

A: Co-efficient of FrictionThe Coefficient of friction is the measure of the relative surface…

Q: A 6-in.-diameter pipe supplies water with a velocity of 5 ft/s. The pipe is made of commercial steel…

Q: Water at 10°C flows through a branched pipe system as shown. Branch 1 is 400 m. long and branch 2 is…

A: Given Data: The data is given as: Diameter of pipe1(d1)=0.075mDiameter of pipe2(d2)=0.1mLength of…

Q: 4) Two tanks of liquid with v-1.02x10-6 ms are connected by two pipes in series as show in the…

A: Given: D1=0.305mD2=0.610mL1=610mL2=9140mE=0.0030ma=0.0566 m3/s To find: H

Q: A pipeline is being designed to pump 0.5 m3 /s of water at 25°C through a concrete pipe. The…

Q: A system of pipes consists of 250 mm pipe 760 m long, and 200 mm pipe 110 m long. If Q = 40 li/sec,…

Q: a. Find an expression for V₂. b. Find the initial time that V₂ first is zero. c. Find the mean…

Q: Three pipes are connected in series. Pipe 1 has length of 850m and diameter of 600mm. Pipe 2 has…

Q: 4 KNm F 6m im 6 KN €1=40, mkN Ex 4m Regd. Oc 2-Y max {- 400

A: Given Length of beam = 11 m Uniform varying load = 6KN /m

Q: QI: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the…

Q: Shown in the figure below. Determine the velocity in the pipe opening (d=50mm DIA) in m/s ELEV = 50m…

A: ● Solution:- As per the given data :- diameter (d) = 50 mm Elevation at water surface h1= 50 m…

Q: Gate AB in figure below is 6 m long and 2 m wide (into the paper). What is the gate minimum weight…

A: angle of inclination θ=60°vertical height of water =4.0 mheight of C.G of submerged gate below…

Q: A hydraulic pipeline 3 km long and 50 cm in diameter is used to convey water with a velocity of 1.5…

Q: The flow rate of water through the pipe system shown in the figure is 30 lit/s under the total head…

A: Step 1

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

7. Find the equivalent length of pipe 1 to 2 with a diameter of 300mm and the velocity
of line C. Use the figure below and neglect minor losses.
U
1
Pipes
A
B
3C
A
Length
300 m
150 m
250 m
B
00
Diameter
300 mm
200 mm
250 mm
C
10 m
D
f
0.020
0.021
0.020

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Fluid
Please draw diagram and choose the points where the Bernoulli equations are applied.
5. Water is flowing with flow rate 50 liter/s in a sudden enlargement pipe. The diameter of the larger and the smaller pipe are 200 mm and 150 mm respectively. Determine the head loss through the enlargement. (Ans.: 81.6 mm)
6. A plastic siphon hose with D = 1.2 cm and is L = 5.5 m used to drain water (15°C) out a tank. Calculate the velocity in the tube for the two situations given below. Use H = 3 cm and h = 1 cm. a. Assume the Bernoulli equation applies (neglect all head loss). b. Assume the component head loss is zero, and the pipe head loss is nonzero.
NEED COMPLETE SOLUTION. NEED ASAP. Thnak you
Water piping A circular pipe used to discharge water from one reservoir to another reservoir. The fluid is assumed to be viscous. Determine the flow rate and the pressure as A ( consider all head losses). Diameter of the pipe D=6 cm, roughness heigh of the pipe k=0,15cm, minor loss coefficients K1=0,5, K2=K3=K4+K5=1, K6=10, K7=1, kinematic viscosity of water =10^-6 m2/s
In the pipe systems (a), (b), and (c) in the Figure, find the flow and velocity in each pipe and the pressure at points A. Assume all nodes are at identical elevations. m/min 20 m/min 20 m /min P- 1000 kP Sm/min 1500 m 1000 m 455 mm 405 mm 1000 m 405 mm 800 m 255 mm 300 m305 mm 300 m 205 men 1100 m 305 mm 1000 m 305 mm A500 m 205 mm 10 m/min 5m/min 10m3/min 5 m/min 15 m /min 5m/min Elev 300 m 405 mm 2000 m 150 2000 m Elev 250 m 5m/min 10 im/min 6 m/min 205 mm 205 mm 2000 m A 2000 m le) 000
SOLVE AND ANSWER MUST BE IN 3 DECIMAL PLACES
B/ In the pipe systems show, find the distribution of flow, with a friction factor of 0.0165. Assume that minor losses can be neglected. (Use Darcy-Wiesbach)-n D=0.45 m A/ Estimate Q in. Qin -2113.2 L/min 1000 m A 645.624 m D= 0.4 m 800 D=0.45 m 1500 L/min 635.376 m D=0.4 m 3000 L/min 1500 L/min
4G. 40 6:51 10 ... 94 Quizzes A transmission tower shown below is subjected to lateral loads as shown. A =3.7 kN, B =4.6 kN, C =6.4 kN Determine the magnitude of the axial force in member EG (in kN). Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m B-KN 1.8 m C-KN F 1.8 m 2.55 m 2.55 m II