L = 700m 2 4 D = 45cm L = 800m D = 40cm L = 600m L= 700m D = 35cm D = 35cm 1 A L = 700m D = 40cm L = 1200m 3 D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5

L = 700m 2 4 D = 45cm L = 800m D = 40cm L = 600m L= 700m D = 35cm D = 35cm 1 A L = 700m D = 40cm L = 1200m 3 D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Imagine the water level in the tank described rises at a rate of 4 mm/s. Knowing the diameter of the tank is 240 mm, what is the average velocity of the water leaving the tank?
The graphic below shows a reducing section that is part of a vertical pipeline. The pipeline contains an oil (S = 0.8) that is flowing at a rate of 0.6 m³/s. The pressure at the entrance to the reducing section (i.e. the larger diameter section indicated as point 1) is p₁= 200 kPa. The dimensions of the section are: L= 450 mm, D₁= 450 mm and D₂= 300 mm. Assume the temperature as 5°C. Ľ. X P₁ D₂ D₁ Q (2 Determine the force on the reducing section. In your calculations you should neglect losses but include gravity. Draw appropriate diagrams to support your working out. Magnitude of the force: L 1
Branching of pipes
4. A large tank has a height of 5.0 m and an area (in plan) of X m2. It has a small outlet (orifice) at the bottom with a diameter of 20 mm, as shown below. Using a value of C = 0.95 for the orifice calculate: (a) the flow rate of water through the outlet when the tank is full, in litre/s (b) the length of time, to the nearest minute, the water level in the tank takes to fall from 5.0 m to 4.0 m. X = 19 m^2 Plan Area = X 5.0 m Outlet
As shown in the figure, water enters and exits a U-shaped piece of pipe located in the horizontal plane. (1) the total absolute pressure in flange number is 200 kPa and there is a mass flow rate input of 40 kg/sec into the pipe. In flange (2), the total pressure is 150 kPa and there is a mass flow rate output of 30 kg/sec from the pipe. 4 kg/sec from section (3) and 6 kg/s from section (4) are discharged into the atmosphere at a pressure of 100 kPa. By working with relative pressures; Determine the total Rx and Ry forces on the two flanges connected to the pipe. (Answer: Rx = 1545,7 N (←) and Ry = 91,96 N (↑))Note:-Mass flow rate = Specific mass x Flow rate. -Specific mass of water : ?w=1000 ??/?3-A flange is a construction element that is usually produced as a standard for the sealed joining of two machine or installation elements.-The sections (1) and (2) are close enough to each other.-The momentum flow correction coefficient for the fluid entering and exiting the control volume is…
The water speed coming out on the pipe from a cylindrical tank shelter as in the image beside is (in the picture) known g = 9.81 m / s² H is the initial high water (m), l is the length of the pipe (M), t is the time passing. Determine the high H needed to produce water speed v = 5 m/s at t = 2.5 seconds for pipe length L = 4 m, calculate 1. BISECTION 2. False position for initial guess XL = 0 and XU = 2 m Calculate up to £ = 1%
a. 8.71 L/s b. 2.70 L/s c. 4.54 L/s d. 7.64 L/s
In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water
Water flows from the rectangular outlet as shown in the figure. Estimate the flow rate per unit width if h = 80 cm, H = 2 m. The flow rate at the outlet is dependent on the head (H + h/2). Neglect all losses. A. 5.93 m³/s B. 5.01 m³/s C. 4.48 m³/s D. 5.49 m³/s E. None of the above h H
With velocity of 9 m/s in the 234 mm diameter pipe in the figure shown, determine the discharge in pipe 4 in m3/s. Assume f = 0.063 for all pipes and neglect minor losses. The following are the properties of each pipe: Pipe 1 (Length=467 m, Diameter = 234 mm) Pipe 2 (Length=598 m, Diameter = 385 mm) Pipe 3 (Length=307 m, Diameter = 732 mm) Pipe 4 (Length=823 m, Diameter = 312 mm) Pipe 5 (Length=1191 m, Diameter = 512 mm)
The three-cistern system in the figure contains water. If L1= 2000 m, f 1= 0.013, D1 = 1m; = 2500 m, f = 0.023, D3 = 1.20m. L2 E 2300 m, f2 = 0.02, D2 = 0.60m; and L3 100 m Datum Compute 02 in m³/s. Express your answer in 3 decimal places. 20 m 120 m K
Problem 2: Calculation of the Flow Rate in a Pipeline Figure 1 shows a pipeline which delivers liquid at constant temperature T from point 1, where the pressure is p, and the elevation is z, to point 2, where the pressure is p2 and the elevation 2₂. The effective length of the pipeline, including fittings and expansion losses, is L and its diameter is D. P = P₁ 44 2 -P= P₂ ܕܐ=ܐ Z= Z₁ Figure 1. Liquid Flow in a Pipeline (a) Calculate the flow rate q (in gal/min) in the pipeline for water at 60°F. The pipeline is nominal 6-inch diameter schedule 40 commercial steel pipe with L = 5000 ft, p= 150 psig, pz = 0 psig, z; = 0 ft, z₂ = 300 ft. (b) Do the calculations for several higher values of p: (200 psig max). Plot the calculated flow rate as a function of pressure difference. Based on the plot, determine the minimum pressure difference needed to start the flow.