2. Water is flowing with velocity 2.2 m/s in a 50 mm diameter 90° close radius bend. Determine the head loss through the bend. (Ans.: 185 mm)

Q: The head of water over v-notch of angle 60° is 50 cm. The flow measured by it is to be with an…

A: Given: Water head, H = 50 cm Accuracy = 1.5%

Q: A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe.. The walls of the…

A:

Q: - 520ft D = 20 in L=20,000 ft B VB PB 400 ft A 20-inch diameter pipe carries 4 ft³/s of water from…

A: The discharge through the pipe, Q = 4 ft3/secThe diameter of each pipe, d = 20 inchesThe length of…

Q: 31-45. The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use…

A:

Q: Water is discharged through the drain pipe at B from the large basin at 0.03 m^3 /s. If the diameter…

A: Given : Discharge through the drain = 0.003 m3/s Diameter of drainpipe = 60 mm To Find : Determine…

Q: 8-62 A horizontal pipe has an abrupt expansion from D₁ = 8 cm to D₂ = 16 cm. The water velocity in…

A: We have to find out the downstream pressure P2 and error if bernoulli's equation is used .

Q: P1: Water flows through a pipe of diameter 300mm with a velocity of 5m/s. If the coefficient of…

A: Head loss due to friction: head loss due to friction occurs mainly in the piping networking like…

Q: The flowrate of the flow is 0,20 m³/s in a pipe placed on a horizontal plane. The pipe diameters are…

A: When water flows through pipe, a force is exerted on the pipe by water. To calculate force on pipe…

Q: Answer fast and do calculation

A:

Q: The large tanks A and B are connected by a variable section pipe. The water level in tank A is 2m,…

A:

Q: a cylindrical vessel has 0.5m diameter and 1m height rotates at 10rad/s. initial height of Mercury…

A:

Q: In a stream of 5ft width and 3 ft depth, a plate is placed that has a rectangular orifice 3ft in…

A: Schematic diagram of the given statement:

Q: H.W.: A concrete pipe culvert is to be constructed under road to carry a maximum discharge 9 m2/sec.…

A: The given data is: Discharge, Q=9m3/s Length of the pipe, L=10 m Slope, s=1/100

Q: Water flows with a flow rate of 0.6 cumec through an inclined pipe PQ of length 10 m lengt having a…

A: Flow rate = 0.6 cumecLength of pipe PQ = 10 mAngle = 30 degreePressure = 30 kN/m2We have to…

Q: Consider a 12-inch diameter steel pipe (ks = E = 1.5 x 10* ft) which has water flowing under…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The average velocity of the steady flow at A and B is indicated. Determine the average velocity at…

A: Determine average velocity at C,Vc?

Q: Determine the velocity and pressure at sections 2 and 3 if water flows steadily through the pipe…

A:

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A: Given data,  P1 = 12.5 kpa P2 = 11.5 kpa P3 = 10.3 kpa D1= 50 mm D2 = 50 mm D3 = 30 mm Discharge = 5…

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.