gate is partially opened, water flow at 6 m/sec. with a depth of 60 cm. Determine whether a hydraulic jump will occur, and if so, which type is it? How much its height (D2-Di) and find the head loss through it? D2 1 D, 1+ 8Fr,2

Q: Answer the following with (True) or (False): 1- A siphon is a closed conduit designed to run…

A: Reference : Irrigation Engineering Given :  5 statements on weirs and Barrages. To determine : To…

Q: A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as…

A: Asked: To determine the difference in pressure between the smaller and larger diameter sections.…

Q: Q1-10: There is a sluice gate at upstream section of 3.5 m wide rectangular channel (see below…

A:

Q: q3

A:

Q: An orifice on a vertical wall has a head of 1.13 m of oil (sg=0.89). It discharges 6192 N of oil in…

A:

Q: H.W. Design Twin Opening of an Inverted Siphon (8 + 27 + 6) m required to pass Canal Discharge of…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: If a triangular gate of height 3,742 mm and base of 3,568 mm is vertical and submerged in water…

A:

Q: Three locations are supplied with a big water tank. Determine the flow rate at the pipes and at the…

A: Given that :-Cross-sectional area of pipes and exits (d₁ = d₂ = d₃ = d₄ = d₅) = 0.01 m²Heights of…

Q: 6m c FH FR TR Fv SLUICE GATE r=6m 30⁰ 30° O QUIR CALCULATE THE MAGNITUDE OF THE RESULTANT FORCE IN…

A:

Q: As shown in Fig. determine the submerged depth of concrete cylinder (h), for equilibrium the gate…

A:

Q: 4.2m SCHAIN RA CHINGE) GATE 60° 1m The 1 meter diameter gate shown weighs 450N and is hinged at "A"…

A:

Q: a)There are three (3) possible cases for curved areas depending on where the water is situated. Give…

A: Given,  There is A Tainter gate which is used to control the flow of water.  Our aim is to Define…

Q: Check the hydraulic structure shown below against piping and then find the thickness of floor at…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: A 2.75-m-Ø wood-stave pipe has 9 m³/s of water entering through a horizontal 30⁰ reducing bend where…

A:

Q: Q- An orifice is located at side of tank with water level is 1.5 m above the centre of orifice.…

A: Water level y=1.5 m, Distance x=0.8 m, Vertical fall h=0.2 m,

Q: Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downward such…

A:

Q: Q.4.A..A (3m) high, (5m) wide rectangular gate is hinged at the top edge at (A), and is restrained…

A:

Q: Q3-A) A hydraulic jump was occurred in a 6m wide rectangular channel. The discharge of flow (Q ) is…

A: Using basic definitions and relationships

Q: A thin 5-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge…

A: Width=5ft Diameter of drain pipe=2ft L=2ft To find minimum water depth(h)

Q: QI: A horizontal rectangular channel of constant cross section has a sluice gat. When the gate is…

A: Given data Velocity at section 1 Depth at section 1 To find  Will hydraulic jump occur Its type…

Q: Q1/Draw the followings: 1- Four pipes of different physical properties connected in parallel. 2-…

A: Note:-  Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A 4m-long quarter-circular gate of radius 3 m and of negligible weight is hinged about its upper…

A: Given:- length of quarter circular gate = 4 m Radius of quarter circular gate = 3 m Weight of gate…

Q: Decide the flow condition after the gate when it is opened partially (free or submerged), then find…

A:

Q: 3. An open circular cylinder of 1m diameter and 2m depth is completely filled with water and rotated…

A:

Q: The weight and diameter of the block are 56,12 kN and 1 m, respectively. Determine the height of H…

A:

Q: a. For horizontal system, if (P1-P=80OkPa), velocity for pipe A =2.5m/sec, coefficient of friction…

A: P1 - P2 = 800KPa Coefficient of friction for all = f = .023 Diameter of all pipes = d = 10cm…

Q: For the pipe transition below, find pressure at point B. Water is moving downward from point A to…

A:

Q: A thin 3-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge…

A:

Q: 3. What is the difference in the position of the pressure center (h.) for the gate if it is…

A:

Q: A vertical gate 1.50 m wide and 2.0 m high has water on one side and is inclined 45° with the…

A:

Q: Water flows through the elbow. It exits to the atmosphere at section 2. The inlet and exit pipe…

A:

Q: Design an inverted syphon required to pass canal discharge of 4.2 m³/sec under a canal with 0.3 m…

A: An inverted Syphon is used to carry storm wastewater discharge or sewage in the ground.In this…

Q: A- A regulator with discharge = 22m 3 /sec , rounded entrance is used for piers and abutment , water…

A: Given; Discharge=22m3/sec Water level at flood time=92.8 Bed level=90.3m(u/s) D/s water level=92.2m…

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.