P. 7.48 - A water discharge of 8 m³/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7 V/2g (V is velocity in the pipe), how much power will have to be supplied to the flow by the pump to produce this discharge? Assume a = 1.0 at all locations. | Elevation = 40 m Water Pump m - Elevation - 20 m Elevation = 10 m 300 m 300 m

P. 7.48 - A water discharge of 8 m³/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7 V/2g (V is velocity in the pipe), how much power will have to be supplied to the flow by the pump to produce this discharge? Assume a = 1.0 at all locations. | Elevation = 40 m Water Pump m - Elevation - 20 m Elevation = 10 m 300 m 300 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1 . List 4 functional of Hydraulic Structures and 4 examples of Hydraulic structures
Ssooolllv
The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Determine the horizontal component of the hydrostatic force against the quarter circle wall. 18 40 18m Unit of the Correct Answer: KN 18m Decimal Places required in the final answer: 1
Q1
A flow of 19 L/s of water passes through a 4" diameter pipe and material with a roughness of 0.20 mm. Two points A and B of this pipe, 456 m apart, are such that the piezometric elevation at B is equal to the geometric dimension at A. Determine the pressure load available at point A, in mca The direction of flow is from A to B. Note: Piezometric dimension corresponds to the sum of the pressure load with the geometric (topographic) dimension m i: CPi=pi/γ+zikinematic viscosity of water = 10-6 m2/s
In tubing outflow performance, as the water cut increased the resultant flow rate increased. true or false
4. A sharp-edge orifice in the vertical wall of a large tank has a diameter of 25mm, Cc=0.62 and Cv = 0.98. If the jet drops 0.94m in a horizontal distance 2.5m from vena contracta. Determine the head and the discharge. Draw the sketch. wwww
2. Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. You have 32KPA, an oil of height 1m (sg.gr.=D0.8), water with height of 1.5m, and glycerin with an sg.gr.=1.26. Ait p#32 kPa 1 m Water 1.5 m 2 m 3 m 60°
A pipe carries an oil of specific gravity 0.8 with pressure 19.62 kPa. The pipe is 3.5 m above datum level. What is piezometric head in meters?
PROBLEM 2:A triangular gate having dimensions shown is hinged at its top at A. The gate rests on a frictionless surface at B. 4m seawater (SG=1.031) 60° 2m BA a. Determine the hydrostatic force acting on the gate. * Your answer b. At what distance from the centroid of the panel is the hydrostatic force acting? * Your answer IMI 21
A line source of strength 15 m/s is situated within a uniform stream flowing at -12 m/s (i.e. right to left). At a distance of 0.6 m downstream from the source is an equal sink. How far will the stagnation points be from the nearest source/ sink?
aceeleration = 4.905 m/s^2 to the right What is the gage pressure at A? in kpa.