Determine the following for the curved surface as shown in the diagram below. The curved surface is of a circle with radius of 0.85 m and has a length into the page of 2.5 m. (a) What is the hydrostatic force acting on the curved surface from A to B? (b) Show the line of action on the diagram and the angle at which it is acting. 1.2 m 0.85 m 1.0 m Curved (1/4 circle with surface r=0.85 m) B2-

Determine the following for the curved surface as shown in the diagram below. The curved surface is of a circle with radius of 0.85 m and has a length into the page of 2.5 m. (a) What is the hydrostatic force acting on the curved surface from A to B? (b) Show the line of action on the diagram and the angle at which it is acting. 1.2 m 0.85 m 1.0 m Curved (1/4 circle with surface r=0.85 m) B2-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Considering the unit length of the dam, when the water level rises to the dam crest level (the highest level) in the dam, the section of which is given in the figure; a-) By accepting the base as impermeable; Determine the weights of regions 1,2 and 3 of the dam, the horizontal and vertical components of the pressure forces acting on the dam, and find the perpendicular distances of the action points of these forces to the O point. (X=3 m, Y=3 m, Z=8 m, H=22 m and γdam=2.4 t/m3 shall be taken.) b-) By accepting the base as impermeable; Determine the safety factor against overturning. c-) By assuming that the bottom is permeable and the pressure distribution of the groundwater linear; Determine the ground water pressure force due to the ground water and the vertical distance of the effect point of this force to the O point. d-) By accepting the base as permeable; Determine the safety factor against overturning.
A trapezoidal plate shown in the figure is submerged in water is 3.4 m below the surface. The bases of the plate is 4 m and 7 m, respectively. The height is 9 m. Find the hydrostatic force acting on the plate in Newton. Unit weight of water is 9.78 KN/m3. Answer is in KN. Write only the value of your answer. ♡ FFS bp
Q .A beam has a force of 25kN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y - y plane for positions A to F, c) plot the shear stress distribution on a suitable graph, labelling the principal values cross-section as shown in Figure Q. The beam is subjected to a vertical shearing Centre of Gravity X y 30 mm 180 mm y A B -C.-. -E- 10mm x 5mm Figure Q: Beam cross-section 30 mm 10 mm
Show your complete solution.
Statics homework #8
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
A newtonian fluid flows down an infinitely long cyalindrical tube (as shown in the figure below). There is NO applied pressure gradient, and fluid flows down the pipe due to gravity alone.i) Derive the velocity profile (?(?) =?). ii)Find???? ,???iii) Draw the velocity and shear stress profiles, showing the points where ? or ? is equal to zero or at their maximum value.
A square lamina is immersed in water with one of the diagonals vertical as shown in given figure. Calculate the force on one side and the location of the centre of pressure. 0.6 m G G a = 0.6 m
Gate AB in figure below is a homogenous mass of 180 kg, 1.2 meter wide into the paper, resting on smooth bottom B. For what water depth hin meters will the force at point B be zero? Use specific weight of glycerin to be 12360 N/m³ and water to be 9790 N/m3. Water Glycerin h 2 m A 1 m 60° О а. 3.56 оБ. 1.82 О с. 1.12 O d. 2.52
1 Solve the hydrostatic force components of AB, BC, and CD using the general solution. Be sure to include the diagrams in determining the hydrostatic force components.
1) a Compressor with a diameter of 0,65 metres and a thickness (t)= 4mm Sigmax= 42 MPA and Sigmay=84MPA Calculate: The pressure P and Maximum In-Plane Shear Stress Tmaxvlak in MPA 2) an element has undergoing a rotation of Theta= 30 degrees Sigmax= 75 MPA and sigma y= 55 MPA. Calculate X', Y' and Txy" in MPA 3) A uniform Beam with a lenght of 2 metres to a-a and forces N=12kn and V=4kn. Calculate the main stresses sigma1 and sigma 2 [in MPA] 4) an element with the given stresses: Sigmax=75 MPA and Sigmay= 55 MPA Calculate the Absolute maximum shear stress in MPA )Tabsmax)
4. Show complete solution and Write legibly. Choose from the options