Statics homework #8 Will the 200N block shown in the figure be held in equilibrium by the force of 80N? The coefficient of static friction is0.3. What is the actual friction force based on your calculation?P45°Solution:A1. There are in total2. Σ F, = 0 : N =3. Fx = 0: fquired4. Maximum static friction fm =5. Hence the block willforces on the block, with the frictional force point to theN;N;→N;6. The actual friction froce on the contacting surface isN→

Answered: Image /qna-images/answer/ddad0a27-20f4-44f3-8720-f90fc1947a88.jpg

Will the 200N block shown in the figure be held in equilibrium by the force of 80N? The coefficient of static friction is 0.3. What is the actual friction force based on your calculation? P 45° Solution: A 1. There are in total forces on the block, with the frictional force point to the 2. Σ F, = 0 : N = 3. Fx = 0: fquired 4. Maximum static friction fm = 5. Hence the block will N; N; + N; 6. The actual friction froce on the contacting surface is N →

Will the 200N block shown in the figure be held in equilibrium by the force of 80N? The coefficient of static friction is 0.3. What is the actual friction force based on your calculation? P 45° Solution: A 1. There are in total forces on the block, with the frictional force point to the 2. Σ F, = 0 : N = 3. Fx = 0: fquired 4. Maximum static friction fm = 5. Hence the block will N; N; + N; 6. The actual friction froce on the contacting surface is N →

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the given figure, determine the value of the horizontal force P if the coefficient of static friction in all contact surfaces is 0.40. ... 200kg -- 2 wedge
2:37 6.00 KB/S A 2M 3M B Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as shown. Each copper rod has an area of 900mm2 and E=120GPA, and the allowable stress is 70MPa. The steel rod has an area of 1200mm2, E=200GPA and the allowable stress is 140MPA. Determine the largest load P which can be supported. Your answer Figure for Problem 2 STEEL 24OMM COPPER COPPER 16OMM 16OMM --
2. A 1.25-kg block was released from the rest position at A by a compressed spring (k = 100 N/m). The coefficient of kinetic friction between the block and the floor is k = 0.25. The uncompressed length of the spring is 1 m. The curved ramp from B to C is frictionless and the block loses contact with the ramp after passing point C. The path of the block is represented by a broken line. Determine (a) the velocity of the block at points B and C. Also, calculate (b) the normal force at point C just before the block left the ramp. (VB = 0.3082 m/s →, Vc = 3.4041 m/s 45°, N = 1.4285 N 71 45⁰) 0.75 m A 1 m B 2 m O 45⁰ 2 m G
SITUATION 32 The simply supported beam in the figure below has a rectangular cross section 120 mm wide and 200 mm high. a. Compute the maximum bending stress in the beam. a. Compute the bending stress at a point on section B that is 25 mm below the top of the beam. 0.8 m RA 6 kN/m B 2m NA с 120 mm 15 kN D A 100 mm -+ 100 mm 1.0 m E RE
A uniform concrete slab is supported by the two cables as shown. Compute the vertical displacement of the concrete slab. steel Area=300sq.mm L=5m 1m P=18N 4m W=25N Aluminum Area 500sq.mm L=3m
SITUATION 8: A suspended bar system consists of two cross sections as shown in the figure. Initially its lower surface is 0.8 millimeters above the ground surface. Take E=205 GPa. 80 I1.2 m mm? 160 40 kN mm2 0.8 mm 20. Determine the stress in the 160 mm2 section when a load of 40kN is applied as shown. a. 90.8 MPa b. 204.6 MPa с. 318.3 МPа d. 147.7 MPa 21. Determine the stress in the 80mm2 section when a load 40 kN is applied as shown. а. 90.8 MPа b. 204.6 MPa с. 318.3 МРа d. 147.7 MPa |42.4 m>4
Q#4. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure). What force is required to just enable the block to move. Consider two cases related to force (a) Pushing force (b) Pulling force P 25° 150N
4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the loads as shown in the figure. Determine the shear stress at the glued section of the beam. 500 N/m 300 N/m A B 3m tuwir. 0
The 58-kg crate is stationary when the force Pis applied. Determine the resulting acceleration of the crate if (a) P = 0, (b) P = 237 N, and (c) P = 520 N. The acceleration is positive if up the slope, negative if down the slope. H, = 0.33 H =0.25 58 kg 21°
2. The block of weight W2 is being held in its position by two cylindrical rollers resting on inclined surfaces. All contact surfaces have a coefficient of static friction, u, = 0.36. W, is given from the table of values. Ms w1 = 400 KN W, W, W2 a. What maximum value of W2 it can be before slipping of the block happens? b. Determine the normal force reaction against the inclined surfaces.
The block of weight W2 is being held in its position by two cylindrical rollers resting on inclinedsurfaces. All contact surfaces have a coefficient of static friction, us = 0.36. W1 = 400KN. a. What maximum value of W2 it can be before slipping of the block happens?b. Determine the normal force reaction against the inclined surfaces.
Determine the minimum diameter of a solid bar which is required to transmit a torque of 40 kNm if the yield stress of the material of the bar is 120 N/mm?. Ans. 119.2 mm.