2. Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. You have 32KPA, an oil of height 1m (sg.gr.=D0.8), water with height of 1.5m, and glycerin with an sg.gr.=1.26. Air, p# 32:kPa 1 m Water 1.5 m 3 m 2 m 60°

2. Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. You have 32KPA, an oil of height 1m (sg.gr.=D0.8), water with height of 1.5m, and glycerin with an sg.gr.=1.26. Air, p# 32:kPa 1 m Water 1.5 m 3 m 2 m 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 94 In the figure, in +he water 0,IM -(2) Alow in the T -shapped pipe inthe horizental plane, the…

A: Following is the given T-Shaped pipe in the horizontal plane: To find: x and Ycomponent of the…

Q: Water flows through a pipe at 144 L/s that changes gradually in diameter from 188 mm at point A to…

Q: Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two…

A: Given data Hydraulic head at 1 (h1) = 66cm Hydraulic head at 2 (h2) = 54cm Travel distance (L) =…

Q: دلها ↓↓ P 7 B vwx What is the Reaction Force induced in the following system at point A, if? Wo = 7…

A: A beam is given we need to find out the reaction at A

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

Q: In fi. If h1= 1 m, h2=. 0.5 m. what is the pressure at. A ?(. SG1= 0.7, S.G2= 0.8) s.g.1 h2

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: Home wok 2 Example ( 8) Steel tube shaft having length 3mm and diameter 50mm subjected to axial…

Q: In fig. if water level = 2 m and the liquid * ?--- =S.G=0.85 , hl %3D Water Ah A' B' 2.35 m. 3.35 m…

Q: A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the…

Q: => AN SPECIFIC ACTING ON THE VERTICALLY OPEN CUBICAL WEIGHT 8 kN/m²³ SIDE UPWARD IN TANK OF UP A AND…

Q: up B What is the total resultant force (kN) that is applied on surface AB? Then find the location of…

Q: compute the force acting on a 2m diameter gate which is inclined 60 degree from the vertical if the…

A: Given that diameter of gate is 2 m. Specific gravity of oil is 0.87. Vertical height of oil above…

Q: A U-tube differential manometer connects two pressure tubes A and B. Pipe A contains carbon…

A: 1. Pressure in Pipe A () = 120 kPa2. Specific gravity of carbon tetrachloride in Pipe A () = 1.63.…

Q: 1. The Dam ABC has a width of 30 m into the paper and the dam bottom length is 60m. The dam material…

A: We will calculate each moment and find FOS.

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

Q: -80mm ↓P=240KN 0.6m P E=70 GP₂ ✓=0.3 800 KN 2 - A circular tube is loaded in compression, as shown…

Q: 3. From d figure below, if the atmos. pressure is 770mm of Hg, fınd: a) Rm if the pressure at B is…

Q: Compute for the unknown pressure at A. = 90 cm; h2 = 150 cm; h3 = h4 =65 cm). Encode your answer…

Q: Oil surface 2.1 m Water surface Oil 0.9 m Hinge Water 1.8 m

Q: ... А 30° 2.5m Water hinge L = 2m In the figure shown, a quarter circle gate AOB is hinged at point…

Q: answer number 1. write your solution in any paper

A: Diameter of gate= 2m To find resultant force acting on the gate

Q: GIVEN: VERTICAL thATE HIN GED LIQUID I Im %3D LHINGE GATE 2m Fi LIQuin を 3m

Q: For the figure shown, calculate the elevation of the pressure head at the junction (P). Round off…

Q: (Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine…

A: The values and diagram given in the question are as follows: Specific gravity of alcohol(Sg)=0.78

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

Q: Bernoulli. Water is siphoned from a large tank filled to a depth of 3m using a tube (Dr=0.6 cm) with…

A: Bernoulli's theorem : In fluid dynamics, Bernoulli's theorem describes the relationship between…

Q: -8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the…

A: Given data Hydraulic head at section-1 (h1) = 66cm Hydraulic head at section-2 (h2) = 54cm Length…

Q: p 18.46kPa Figure 34(01)A A OR, s 0.8 7 m 6 m 2 m

Q: In fig. if H= 88 inches, the difference in pressure =---?(the fluid is water) Piezometer (static)…

Q: Calculate the following values: a) Yield Force (Fy) that will cause the system to yield at point A.…

A: A cantilever beam with point load, F and moment curvature relationLength of the beam, L =3.5 mLength…

Q: The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator…

Q: (a) the imaginary height of the liquid from level AB, (b) the magnitude of FH, (c) the magnitude of…

Question

2. Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. You have
32KPA, an oil of height 1m (sg.gr.=D0.8), water with height of 1.5m, and glycerin with an sg.gr.=1.26.
Ait p#32 kPa
1 m
Water
1.5 m
2 m
3 m
60°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
What is pipe roughness? A pump is located 5 m above the surface = 8170 M/m¹) in a closed tank. The pressure in the space above liquid surface is 35 Kpa. The suction line to the pump is 15 m of 15 cm diameter pipe (/= 0.025). The discharge from the pump is 60 m of 20 cm diameter pipe (/= 0.03). The pipe discharges in a submerged fashion to an open tank whose free liquid surface is 3 m lower than the liquid surface in the pressure tank. If pump puts 1.5 kW Into the liquid, determine the flow rate and the pressure in the pipe on the suction side of the pump. Assume turbulent flow.
Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. Ans. F= 733.16kN, 1.844m from the bottom of the tank parallel to the gate
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
answer number 2.show your solution asap
SHOW SOlution Ans. F= 733.16kN 1.844m from the bottom of the tank parallel to the gate
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
3. What is the pressure difference between pipe A and pipe B? Give pressure difference in kPa. (y = 1.22 m and h 30 in.) The gage fluid, M, is mercury with a specific gravity of 13.54 State assumed values if any. Water A Water B y D Liquid M
Compute for the unknown pressure at A. (h1= 90 cm; h2= 150 cm; h3=h4= 65 cm). SG salwater = 1.024 Oil SG-0.8 h1 h3 h2 A• h4 Salt Water PA= ? Mercury SG 13.6 %3D
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°