1.8mA square vertical surface 1.8m shown has its upper edge horizontal on the liquid surface. At what depth "X" must a horizontal linebe drawn as to divide it into two parts, on each of which the hydrostatic force on the top is the same at the bottomA1.14 mB) 1.27 mNo answer among the choicesD) 1.43 m1.36 m

Given data in question Domesions Square plate Hydrostatic force is equal in above and below part of…

Answered: ... 1.8m A square vertical surface 1.8m…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SAMPLE PROBLEM 1. A square plate having a length of 3 m and width of 2 m is immersed in water. Determine the hydrostatic force in kN acting on the plate and the location of the center of pressure measured from the water surface if: a. The top of the plate coincides with the water surface. b. The top of the plate is located 5 m below the surface. c. If the plate is inclined at an angle of 30° with respect to the horizontal. a) Fin = 2m Pog: A %3D 1-5m h Yp Pg (981. Sm 1. Peg= 14.72 Kla %3D
A Tainter gate used to control water flow from the Uniontown Dam on the Ohio River is shown; the gate width is w = 34 m. Please show complete solution.
A 2.8 - m square plate is immersed in water in a vertical position such that the two edges of the square are horizontal. The immersion is such that the center of pressure on the plate is 8cm from its center of gravity. Determine the distance from the water surface to the center of pressure. (A) 7.67m B 8.67m 9.21m 8.25m D
Civil engineering -Hydraulics
A curved surface was submerged in water as shown. Calculate the vertical component of the hydrostatic force on the curved surface. The system is 2m wide into the paper. 5m 60° r = 2m
A triangle ABC is shown below (not to scale). Surface ABC is flat and homogeneous. Surface ABC is submerged vertically in the water. AB-AC-6 m. Angel BAC is 90°. BC is parallel with the water surface at a distance of 10 m. The system temperature is 30 °C. (A) What is the magnitude of the total hydrostatic force acting on ABC? (B) What is the vertical distance from the point of action of the total hydrostatic force to the surface of the water? t sheet: Water surface B C TABLE 2.1 Surface Area, Centroid, and Moment of Inertia of Certain Simple Geometrical Plates Area Centroid Moment of Inertia About the Neutral x-Axis
3.58 As shown, a round viewing window of diameter D = 0.8 m is situated in a large tank of seawater (S = 1.03). The top of the window is 1.2 m below the water surface, and the window is an- gled at 60° with respect to the horizontal. Find the hydrostatic force acting on the window and locate the corresponding CP. Sea water h 60° PROBLEM 3.58 Window
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the center of pressure from the water surface. O 9.21m O 7.67m O 8.67m O 8.25m
Question 3 Water is flowing in a rigid pipe, the pressure wave travel will velocity (c) 950m/s. The value of compressibility of fluid is 6×10-10 m² N Assume velocity of water V = 4m/s. . The value of water hammer pressure will be:
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the distance of the top of the plate from the water surface. O 6.8m O 6.3m O 7.3m O 7.8m
A triangular gate having dimensions shown is hinged at its top at A. The gate rests on a frictionless surface at B. A.) Determine the hydrostatic force acting on the gate. B.) At what distancce from the centroiid of the panel is the hydrostatic force acting?
please answer with a neat solution and provide all answersA curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w = 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m.Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer.Determine the vertical component of the hydrostatic force (in N) acting on the gate, indicate the direction by putting an U for upward and D for downward after your numerical answerDetermine the magnitude (in N) of the hydrostatic force acting on the gateWhat angle (in degrees) does the hydrostatic force F make with horizontal?

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS