The figure below shows a branched system in which the pressure at A is 700 kPaand the pressure at B is 550 kPa. Each branch is 60 mlong.Neglect losses at the junctions but consider all elbowsin both branches. If the system carries oil with a specific weight of 8.80 kN/m3, calculate the total volume flow rate.The friction factor of the DN 100branch (call thisBranch a) is 0.02and the friction factor of the DN 80branch (call this Branch b) is 0.022. Assume all elbows are standard.(Answer: 6.07×10−2?3/?)

Q: An inverted right circular conical tank loses water out of a 4-in hole at the bottom. The radius of…

A: Solve for dh/dt and dv/dt

Q: Two parallel plates kept 295mm a part have laminar flow of oil . The lower plate is stationary and…

A:

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

A:

Q: Determine the force acting on hydraulic cylinders ED and AC if the excavator applies a 20 kN force…

A: Given -

Q: 9-14. The flat belts are moving at the speeds shown. Plot both the velocity profile within the oil…

A: Given data: Dynamic viscosity, μ=0.45 N.sm2 Density of oil, ρ=920 kgm3 The shear stress is directly…

Q: pipe (d = 80 mm). I pe is 2000 kN/m² th um velocity. flow of oil. ictional drag over 1 tress at 10…

A:

Q: Consider a laminar flow in the x-direction between two infinite parallel plates (Couette flow). The…

A:

Q: d. Situation XXI. A 20 cm diameter pipe length of 100 m with z = 60 m, f 0.02 m and loss of head due…

A: Solution:- Given details: Diameter of pipe, d =20 cm, Length L =100 m. Head loss coefficient k =0.5…

Q: COMPUTE THE CAPILLARY RISE IN mm. OF PURE WATER AT 10^0 C EXPECTED IN A 0.8 mm θ  TUBE

A:

Q: 4. A welded cylindrical drum is made of steel plate. It has an internal diameter of 1.50 m and its…

A: Given Data Diameter of cylinder (d) = 1.5 m = 1500 mm  Thickness of wall (t) = 12 mm  Internal…

Q: he hydraulic uylinder is extending with the velocity and aceeleration Sronn. Determine the velocity…

A: Whenever the speed of any particle changes, it creates acceleration. The rate of change in angular…

Q: In a smooth pipe of uniform diameter 30 cm a pressure of 60 kPa was observed at section 1 which was…

A:

Q: Consider a laminar flow in the x-direction between two infinite parallel plates (Couette flow). The…

A: Given- Laminar flow in the x-direction, 2 infinite parallel plates (Couette flow), Velocity of upper…

Q: A fluid (sp. gr. = 0.9, u= 1.2 Pa-s) flows in a laminar state between two stationary parallel plates…

A: Given: A fluid (sp. gr. = 0.9, μ= 1.2 Pa/s) flows in a laminar state. μ=1.2 Pas=1.2 N.sm2. Two…

Q: covered with 2.8 m ker

A: According to Given data Tank Contains 5.7 m water Covered with 2.8 m of keroseneTo find the gauge…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A:

Q: Three smooth identical cylinders A, B and C stacked in a V-shaped trough as shown (weight 400 N and…

A:

Q: n oil of viscosity 0.021 vo stationary parallel 5 mm apart. The veloc lates is 3 m/s. The pres ow is

A:

Q: Consider a laminar flow in the x-direction between two infinite parallel plates (Couette flow). The…

A: A laminar flow in the x-direction (Couette flow)- Lower plate at rest, The velocity of the upper…

Q: The pressure gauges are inserted at A and B in a vertical pipe converging water.  The diameters at A…

A:

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: Given -

Q: Problem 2.. The internal pressure of a cylindrical tank is given as 1200 KPa. If the allowable…

A:

Q: SITUATION B. An open tank containing brine (SG = 1.3) is accelerated vertically at 7.5 m/s2.…

A: Given data:- Specific gravity of brine, SG = 1.3 Accelerated vertically at 7.5 m/s2

Q: An upward flow of oil (mass density 800 kg/m°, dynamic viscosity 0.8 kg/m-s) takes place under…

A: Mass density of fluid (ρ) = 800 kg/m3 Dynamic viscosity (μ) = 0.8 kg/m-s Diameter of pipe (D) = 0.1…

Q: Review the three cases of flow through porous media shown below. For each case, consider and…

A: This is a question about Darcy’s law, which describes the flow of a fluid through a porous medium.…

Q: An upward flow of oil (mass density 800 kg/m3, dynamic viscosity 0.8 kg/m-s) takes place under…

A:

Q: A cylindrical pressure vessel with a diameter of 600 mm is to be fabricated from steel plates of…

A:

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

A:

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity 0.8 kg/m-s) takes place under…

A: Given- Mass density = 800 kg/m3 Dynamic viscosity=0.8 kg/m-s Pressure at sections 1 and 2 are- 435…

Q: In a uniform diameter smooth pipe measuring 30 cm, a pressure of 60 kPa was measured at section 1,…

A:

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

A: Given data  Density of oil = 800 kg/m3 Dynamic viscosity= 0.8 kg/ms  Diameter of pipe (D) = 0.1 m…

Q: (b) An oil having a viscosity of 0.096 Ns/m² and a specific gravity of 1.59 flows as a laminar flow…

A:

Q: The hydraulic cylinder extends at 0.5 m/s and determine the angular velocity and the angular…

A: The given figure is shown below:

Q: Water at 300C flow in a Venturi meter with the velocity 3 m/s. The tube diameter at station 1 is D1…

A: velocity at station 1V1=3 m/stube diameter of station 2D2=30 cmpressure at station 1P1=30 Kpa…

Q: p 18.46kPa Figure 34(01)A A OR, s 0.8 7 m 6 m 2 m

A:

Q: Consider two wells separated a distance L from each other. Assume porous media with v=-(K/μ)Vp where…

A: Streamline Flow : The flow of the water is determined by streamflow. The flow of fluid in case of…

Q: The water tank has a rectangular crack on its side having a width of 100 mm and an average opening…

A: width of crack (wc) = 100 mmopening of crack (Lc) = 0.1 mmT=20o CLength of crack (L) = 200 mmh=2 m

Q: 4. In a vertically submerged plane surface, pressure at evbery point remains same a) True b) False

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.