Q/Along flexible strip Looting of 2.5m width having a smooth base, is subjected to aurilor distributed load of 80 kN/m². Determine the vertical stress intensitres al adepth of 2m below: i) center line of the looting 2:5 (i) at side face of the looting 2m iii) at a point 1-5m, from the side lace t T₂ = = = = [2 + Sin α cos (d+ 2B)] 옺[a A B 94

Q/Along flexible strip Looting of 2.5m width having a smooth base, is subjected to aurilor distributed load of 80 kN/m². Determine the vertical stress intensitres al adepth of 2m below: i) center line of the looting 2:5 (i) at side face of the looting 2m iii) at a point 1-5m, from the side lace t T₂ = = = = [2 + Sin α cos (d+ 2B)] 옺[a A B 94

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T=780 N⋅m. The allowable shear stress for the material is τallow=52 MPa. Determine the required diameter d of the shaft.
oblique surface Aprismahc bar is'under tenstn, 24N 24N bar has a size (3cm XaCm) in width ond de pth respectively. 30° Determine tha normal stress on the jiven ablique sur foce.
The horizontal force P = 50 N is applied to the upper block with the system initially stationary. The block masses are ma = 10 kg and mg = 5 kg. Determine if and where slippage occurs for the fol- lowing conditions on the coefficients of static fric- tion: (a) u = 0.40, uz = 0.50 and (b) p = 0.30, uz = %3D 0.60. Assume that the coefficients of kinetic friction are 75 percent of the static values. B 15° A
The beam is subjected to the load at its end. Take P=4.2 kN and V = 2 kN. (Figure 1) Figure 1 of 1 30 mm VV 60 mm 2m B The beam is subjected to the load at its end. Take P = 4.2 kN and V = 2 kN .Determine the maximum principal stress at point B.
o) Drow the shear force and moment orce diaprams fore ams. b)Draw the imapinary r egret on the plan immediately to the left ol the C slie and determine the value of your most sip show- to be made in the region in c Draw the normal drawing the picture C and show the maximum stress valuesby calculating. Pii=21KN h = 30 cm A vy 3,5 m 4,5m b= 20cm
Cross-section of each member is 400 mm2 2 m 19. Determine the normal stress at 2 m member GI. 20. Determine the normal stress at F15m--15m-15m---15m- member BC. 21. Determine the 6KN normal stress at member CJ. 22. Determine the normal stress at member DE.
13. The velocity distribution over a plate is given by u= y-y in which u is the velocity in m/sec at a distance of y m above the plate. Determine the shear stress at y 0, 0.1 and 0.2 m. Take u = 6 poise. [Ans. 0.4, 0.028 and 0.159 N/m)
Determine the maximum normal stress (MPa) in member BC. Let diameter of bar BC be 25 mm. 60 KN K J I ДИМА 3m 3m 3m 3m 3m 3m C D E 80 KN 60 KN L B 40 kN H F 5m
1. If the T-beam is subjected to a vertical shear of V = 12kip, determine the maximum shear stressin the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch thevariation of the shear-stress intensity over the entire cross-section.
Question 03: Determine the normal stress and draw the stress diagram of the beam at a point 1 m from the left support. 1.0m 20KN/M D ↓ ↓ ↓ ↓ J J 2.0m 1=225x106mm² Bean depth = z 300mm
Q1. A horizontal bar of nagligible weight and assumed rigid is supportad by two rads, AB and CD, and hingad : the right and. Data for the rods are as follows: Rod AB: L= 2 m, A= 1950 mm. E= 80 GPa ; Rod CD: L=2.5 m, A= 1200 mm, E= 200 GPa Ifthe maximum unit stress in AB is not to exceed 90 MPa, and the maximum allowabla load for CDis 110 kN, determine the maximum value of the force F. B F 0.60 m. 1.90 m 1.20 m
6O cm 20 20. 20cm 20 cm CrOSS - section 1. Determine the value the max Yalue g mament is 702 kN. cm gbending Stress of 2. Determine the ralue sf shean SKess of the max value g shean is 420 KN -