Letermine the average normal stress in each bar if the diameter of each bar is 20 mm. Set P = 40 kN. TAC ('TU Foints), OBC (10 points), OAB (10 points). 1.5 m 2 m

Q: Determine the state of stress at points K and H on the cross-section of the shaft with diameter of…

A: Diameter of shaft(D)=40 mm Force(P1)=15 kN or 15000 N Force(P2)=18 kN or 18000 N

Q: inclined at 30° to the known directions of the In a stressed member , *0 retio u = 0.3. Determine…

A:

Q: DETERMINE THE AVERAGE NORMAL STRESS DEVELOPED AT MEMBER A, B&C. THE DIAMETER OF EACH SEGMENT IS…

A: Draw the FBD of each segment such that equilibrium is satisfied. The use the definition of stress as…

Q: Two solid cylindrical rods support a load of P 22 kN, as shown. Rod (1) has a diameter of 12 mm and…

A: Given, two solid cylindrical rods. Load P =22 KN Diameter of rod 1 =12mm Diameter of rod 2 =16 mm…

Q: Knowing that a = 1.24 in. determine the largest value of P that can be applied without exceeding…

A: AnswerWe are given Eccentricity of load about XX axis ex = 2.5 in        (perpendicular to XX…

Q: For the given plane stress state '=120 MPa, ' c= 100 MPa and °c=150 MРа, σύ. . Calculate the…

A: Given: σb=120 MPaτc=100 MPaσa=150 MPa

Q: 9-7. Determine the stress components acting on the inclined plane AB. Solve the problem using the…

A:

Q: Refer the beam shown with cross section of thickness, t= 15 mm. If F = 84 kN and a = 150 mm, F 2a…

A:

Q: P2 Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A: Given data : Normal stress in X direction (σX)=-36 ksiNormal stress in Y direction (σY)=-18 ksiShear…

Q: 2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa).…

A:

Q: Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An…

A:

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

A:

Q: Two solid cylindrical rods support a load of P = 22 kN, as shown. Rod (1) has a diameter of 12 mm…

A: The load given in the diagram will be distributed among the solid cylindrical rods of different…

Q: 2. For the beam shown, determine the following: a. Maximum tensile stress in the beam. b. Maximum…

A:

Q: If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24 mm². 1.4 m D…

A: Determine the stress in member CE

Q: The cross-sectional area of bar ABCD is 320 mm^2. Determine the maximum normal stress in the bar.…

A: Given- The cross-sectional area of bar ABCD is 320 mm2 To Find- The maximum normal stress in the…

Q: I jp. sin. 05 in. B. 3 kip A9 kip 8 kip Lc-2 kip

A:

Q: For the beam of section shown, the bending moment =800 kN.m and shear force M 12.5 kN determine the…

A: Given data in question  Moment Dimensions  Shear force To find out  Maximum bending stress Maximum…

Q: inclined at 30° to the known directions of the In a stressed member , *0 retio u= 0.3. Determine the…

A: Let normal principal strain in x & ydirection are E1 & E2Ex1 = Ex+Ey2 + Ex-Ey2 cos2θ2 +…

Q: principal stresses. The strains measured in these inclined at 30° to the known directions of the…

A:

Q: Determine maximum shear stress

A: Given data : Maximum principal stress σP1=32 MPaMinimum principal stress σP2=-28 MPa

Q: 2. If we have the inside shearing stress (point A), T= 50 N/mm. Calculate the outside shearing…

A: This question is related to the Torsion from Strength of Material. In this question we calculate…

Q: inclined at 30° to the known directions of the respectively. E = 2.1 x 10$ N/mm? and Poisson's In a…

A:

Q: 1. Mohr's Circle. Determine the radius of the circle (R) and the coordinates for the center of the…

A: X axis represents normal stress and y axis represents Shear stress.

Q: 2.2m

A:

Q: o solid cylindrical rods support a load of P 22 kN, as shown. Rod (1) has a diameter of 12 mm and…

A: Given ;

Q: y 10 kN 30 cm 10 cm 50 cm 10 cm 300 cm C A OD=-104.16kPa oc=-62.5kPa OA=-20.84kPa OB=-187.5kPa Hint:…

A:

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

A:

Q: Q:8/ A steel wire (10m) lon (2000N). Neglecting the we diameter if the stress is no not to exceed…

A:

Q: 1. The cross-sectional area of bar ABCD is "X" mm². Determine the maximum normal stress in the bar.…

A: The formula to calculate the normal stress is given by, σ=PA                    ...1 Draw the…

Q: The cross sectional area of the bar ABCD is 550 mm2. F1 = 25 kN, F2 = 20 kN, F3 = 35 kN. F1 F2 F3 Be…

A:

Q: The grain of a wooden member forms an angle of 15° with the vertical. Determine the in-plane…

A: Step 1: Step 2: Step 3: Step 4:

Q: A rectangular column of sides 0.4 m × 0.35 m , made of concrete, is used to support a compressive…

A: Solution; Given data; Rectangular column=0.4*0.35 sidesCompressive load=2800 KNDiameter of steel…

Q: Determine the maximum value of Qof the Transverse Shear Stress formula (T (VQ)/(1t)] in mm for the…

A:

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.