The solid 1.45-in.-diameter rod is subjected to auniform axial distributed loading along itslength of w = 725 Ib/ft. Two concentrated loads%3Dalso act on the rod: P = 1600 lb and Q = 1000%3D%3DIb. Assume a = 12 in. and b = 24 in. Determinethe normal stress in the rod at the following%3Dlocations:(a) x = 8 in.(b) x = 24 in.%3D→ → → → -→ ->PBCаbAnswer:Ox=8in.psiOx=24in.psi

Answered: Image /qna-images/answer/23907c38-95d1-4cf9-9fe5-c547ad5a1ea7.jpg

The solid 1.45-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 725 lb/ft. Two concentrated loads also act on the rod: P = 1600 lb and Q = 1000 Ib. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following %3D %3D locations: (a) x = 8 in. (b) x = 24 in. > → → ►P A B C a b Answer: Ox=8in. psi Ox=24in. psi

The solid 1.45-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 725 lb/ft. Two concentrated loads also act on the rod: P = 1600 lb and Q = 1000 Ib. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following %3D %3D locations: (a) x = 8 in. (b) x = 24 in. > → → ►P A B C a b Answer: Ox=8in. psi Ox=24in. psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
thanks
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
2.75 A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at –20°C, find the minimum allowable diameter of the rod. Use a = 11.7 × 10–6/°C and E = 200 GPa. %3D
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
The solid 1.05-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 800 lb/ft. Two concentrated loads also act on the rod: P= 2300 lb and Q = 1400 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in. → → -→ P B a Answer: Ox=8in. = psi Ox=24in. = psi
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
(a) A steel structural member of length = 10 ft. is supported between two fixed supports so that it cannot expand. At 68°F, there is no stress in the member. (E = 30 x 106 psi and α = 6.5 x 10-6/°F) Calculate the stress (psi) in the member at 95°F. Stress (psi) = (b) If the same structural member is not supported between two fixed supports, calculate the total elongation of the member (in.) for the same temperature change. elongation (in.) =
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no