The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 850 lb/ft. Two concentrated loads also act on the rod: P= 2500 lb and Q = 500 lb. Assume a = 15 in. and b = 30 in. Determine the normal stress in the rod at the following locations: (a) x = 10 in. (b) x = 30 in. → → В a b Answer: Ox=10in. = i psi Ox=30in. = i psi

The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 850 lb/ft. Two concentrated loads also act on the rod: P= 2500 lb and Q = 500 lb. Assume a = 15 in. and b = 30 in. Determine the normal stress in the rod at the following locations: (a) x = 10 in. (b) x = 30 in. → → В a b Answer: Ox=10in. = i psi Ox=30in. = i psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 1700 Ib and Q = 600 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x= 8 in. (b) x = 24 in. → - A В IC a Answer: Ox-8in. - psi Ox-24in. psi
6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. Im B OPT. →→→→T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
The solid 1.05-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 800 lb/ft. Two concentrated loads also act on the rod: P= 2300 lb and Q = 1400 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in. → → -→ P B a Answer: Ox=8in. = psi Ox=24in. = psi
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
(a) A steel structural member of length = 10 ft. is supported between two fixed supports so that it cannot expand. At 68°F, there is no stress in the member. (E = 30 x 106 psi and α = 6.5 x 10-6/°F) Calculate the stress (psi) in the member at 95°F. Stress (psi) = (b) If the same structural member is not supported between two fixed supports, calculate the total elongation of the member (in.) for the same temperature change. elongation (in.) =