Problem A solid circular shaft of diameter 120 mm has a collar of 20 mm thickness as shown in Fig. The shaft is subjected to a compresssive force of 250 kN. Determine (i) Compressive stress developed in the shaft. section. (ii) Shear stress developed in collar a P= 250 kN 120 mm 20mm

Problem A solid circular shaft of diameter 120 mm has a collar of 20 mm thickness as shown in Fig. The shaft is subjected to a compresssive force of 250 kN. Determine (i) Compressive stress developed in the shaft. section. (ii) Shear stress developed in collar a P= 250 kN 120 mm 20mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find max and min stresses. Please provide step by step solution. Don't copy!!
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
The question is in the picture. Thanks
Consider the element in with Txy = 30 MPa. 80 MPa Part A 01, 02 Determine the principal stresses. Enter your answers in megapascals to three significant figures separated by a comma. = T vec Submit VE ΑΣΦ | 41 Txy Request Answer
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2700 psi, op2 = -2470 psi, Op3 = 0 (b) op1 = 44 MPa, op2 = 25 MPa, op3 = 0
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…
A water tank 5m in diameter and 5m high is made from steel having a thickness of 12mm. Answer below, a.) When the tank is filled with water, determine the circumferential stress. b.) Determine the longitudinal stress at the bottom of the tank when it is filled with water. c.) If the circumferential stress is limited to 5MPa, what is the maximum height of water to which the tank maybe filled.
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.
show steps At point (A)
a) 0.040 m b) 0.260 m c) 0.020 m d) 0.300 m