Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side. Determine the average normal stress at section a-a and the average shear stress at section b-b inmember AB. The cross-section is square, 0.55 in. on each side.150 lb/ftBC.4 ft60°b.b.

Answered: Image /qna-images/answer/25c7feea-feb3-4053-a8dc-24f54ed41f40.jpg

Answered: average

Engineering

Civil Engineering

average

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
Consider the element in with Txy = 30 MPa. 80 MPa Part A 01, 02 Determine the principal stresses. Enter your answers in megapascals to three significant figures separated by a comma. = T vec Submit VE ΑΣΦ | 41 Txy Request Answer
Determine the average normal stress developed ont he cross section.
If Øxx = 110 MPa, Oyy = - 86 MPa, ozz = 55 MPa. Txy = 60 MPa, and allþther components are zero. Determine the principal stresses and the direction cosines of the principal axis. Also find the octahedral normal and shear stress components. Q.4:
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and Ty = -5 ksi. Draw the Mohr's circle for this stress state. Identify the maximum shear stress from the Mohr's circle, and draw the maximum shear stress element, specifying its orientation.
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 4300 mm² and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A₂ = 2550 mm² and an allowable normal stress of 125 MPa. Assume x₁-23m.x₂-3.9 m.y1 = 1.4 m, and y₂ = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ Answer: Pmax= i| B P ! KN
Q1/ Draw the normal stress distribution over the cross section on which the maximum normal stress occurs. El = 80000 MPa., E2=20000 MPa A 10 kN/m M- 20 kN MATERIAL 10 MM B MATERIAL MATERIAL 2 100 MM MATERIAL 2 -2 M- -40 mm Q2/ the beam in Q1 (a) find the spacing required between Nails 1 (b) find the spacing required between Nails 2, shear force per nails is 70 kN. 50 mm 16 mm Nail 1- 10 MM- 140 mm Nail 2 16 mm
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry